Panasonic AG-HPX371E User Manual
15
Chapter
8
Connecting
to
Exter
nal
De
vices
De
vices
5
SelectOPERATIONFORMAT(HDD)inthe
menuanduseacursorbuttonandtheSET
buttontoselectYES.
menuanduseacursorbuttonandtheSET
buttontoselectYES.
• Select YES in the confirmation message that
appears again to start hard disk drive formatting.
• Handled as a “TYPE S” hard disk drive after
formatting.
NOTE
All data on a hard disk drive is deleted when the disk is
formatted. It is not possible to select part of a partition
to delete.
formatted. It is not possible to select part of a partition
to delete.
Writing to hard disk drive
1
SwitchtotheUSBhostmode.
For details, refer to [Switching to USB Host Mode]
(page 150).
(page 150).
2
ConnectaharddiskdriveviaUSB.
If the hard disk drive has not been formatted by
the camera, format it according to the instructions
provided in [Formatting Hard Disks] (page 152).
the camera, format it according to the instructions
provided in [Formatting Hard Disks] (page 152).
3
InsertaPcard.
4
PresstheTHUMBNAILbuttontoopenthe
thumbnailscreen.
thumbnailscreen.
5
PresstheTHUMBNAILbuttonandselectHDD
EXPORTfromthethumbnailmenuand
specifytheslotofthePcardwiththedatayou
wanttowritetotheharddiskdrive.
wanttowritetotheharddiskdrive.
6
SelectYES.
• This starts the write process.
• A progress bar appears during the write process.
• A progress bar appears during the write process.
To interrupt writing, press the SET button.
Selecting YES in the cancel confirmation that
appears will stop the write process.
Selecting YES in the cancel confirmation that
appears will stop the write process.
• COPY COMPLETED! announces the end of the
write process.
NOTE
• To turn off the verify phase in a write operation, select
HDD SETUP in the thumbnail menu and set VERIFY
to OFF. This speeds up the write time but does not
verify the written data.
to OFF. This speeds up the write time but does not
verify the written data.
• Selecting ALL SLOT writes the data on all inserted P2
cards inserted in the camera to the hard disk drive.
NOTE
• A TYPE S hard disk drive can write data in card units. Up to
23 P2 cards can be saved to a hard disk drive.
The P2 card data recorded on a hard disk drive are
recognized as separate drives.
The P2 card data recorded on a hard disk drive are
recognized as separate drives.
• To write P2 cards with bad clips, it is a good idea to repair
these clips before writing them to a hard disk drive.
• Ending a recording during the verify phase will end writing of
data from the P2 card to the hard disk drive.
Writing back data to P2 cards
This allows you to select a clip from the hard disk drive and
write it back to a P2 card.
write it back to a P2 card.
1
SwitchtotheUSBhostmode.
For details, refer to [Switching to USB Host Mode]
(page 150).
(page 150).
2
ConnectaharddiskdriveviaUSB.
3
InsertthePcardtowhichdatawillbewritten
backto.
backto.
4
PresstheTHUMBNAILbutton,selectHDD
EXPLOREfromthethumbnailmenu,moveto
thepartitionwiththedatathatwillbereadand
presstheSETbutton.
EXPLOREfromthethumbnailmenu,moveto
thepartitionwiththedatathatwillbereadand
presstheSETbutton.
5
SelectthecliptobewrittentothePcardfrom
thethumbnailontheharddiskdrive.
thethumbnailontheharddiskdrive.
6
PresstheTHUMBNAILbutton,select
OPERATIONIMPORTSELECTEDCLIPS
fromthethumbnailmenuandselecttheslotof
thePcardtowritethedatato.
OPERATIONIMPORTSELECTEDCLIPS
fromthethumbnailmenuandselecttheslotof
thePcardtowritethedatato.
7
SelectYES.
• This starts the data write to the P2 card.
• When the write process ends, “COPY
• When the write process ends, “COPY
COMPLETED!” appears.
NOTE
• When clips are selected for writing, verify is not performed.