Panasonic AG-HPX600EN User Manual
– 154 –
Chapter 10 Maintenance and Inspection — Inspections before shooting
Inspections before shooting
Before recording, perform the following inspection to ensure that the system operates properly. It is recommended that you check the image using a
color video monitor.
color video monitor.
Preparing to inspect
1
Attach an adequately charged battery.
2
Turn the <POWER> switch <ON>, and check the battery
charge level indicator on the viewfinder screen.
If the remaining battery level is low, replace the battery with an
adequately charged one.
adequately charged one.
9 9 min
1 - C L
B 9 0%
U S E R - 1
I P
C AC
Z x 2
D
3
Insert a P2 card into a card slot and close the slot cover.
f
Ensure that the P2 card access LED lights in orange for the card
slot to which the P2 card is inserted. If both card slots have P2
cards inserted, the orange access LED for the P2 card slot of the P2
card inserted first (the one that completed an access first) lights up,
and the green P2 card access LED for the P2 card inserted second
lights up.
slot to which the P2 card is inserted. If both card slots have P2
cards inserted, the orange access LED for the P2 card slot of the P2
card inserted first (the one that completed an access first) lights up,
and the green P2 card access LED for the P2 card inserted second
lights up.
f
If the P2 card access LED for the P2 card slot to which the P2 card
is inserted flashes in green or does not light up, that P2 card is not
available for recording.
is inserted flashes in green or does not light up, that P2 card is not
available for recording.
1
2
Inspecting the camera unit
1
Set the zoom to the electric zoom mode and check the
behavior of the electric zoom.
Ensure that the image changes between telescopic and wide-angle.
2
Set the zoom to the manual zoom mode and check the
behavior of the manual zoom.
Rotate the manual zoom lever and ensure that the image changes
between telescopic and wide-angle.
between telescopic and wide-angle.
3
Set the iris to automatic adjustment mode, and ensure that
the automatic adjustment works when the lens is pointed at
objects with different degree of brightness.
4
Set the iris to manual mode and rotate the iris ring to check
the manual iris adjustment.
5
Set the iris back to automatic adjustment mode, and check
the followings by switching the <GAIN> switch setting to
<L>, <M>, and then <H>:
f
The iris is adjusted for objects with same degree of brightness as
the setting changes.
the setting changes.
f
The gain value display on the viewfinder screen changes as the
setting changes.
setting changes.
6
If a lens with an extender is attached, set the extender to its
usage position to ensure that it works properly.
Inspecting the memory recording functions
Inspecting the P2 card recording
1
On the viewfinder screen display, ensure that the remaining
P2 card capacity is sufficient.
2
Press the <REC> button and check the following:
f
The orange P2 access LED flashes.
f
[REC] is displayed on the viewfinder screen.
f
No system warning is displayed on the viewfinder screen.
3
Press the <REC> button again.
Ensure that the P2 access LED turns to orange, and that the [REC]
display disappears from the viewfinder screen.
display disappears from the viewfinder screen.
4
Use the <REC> button on the handle to check the same
Perform the same inspection for the VTR button on the lens.
5
Press the <THUMBNAIL> button to switch to the thumbnail
screen, and from the thumbnail, playback the clip you just
recorded.
Ensure that the clip plays back properly.
6
If two P2 cards are inserted in the P2 card slots, press the
<USER> buttons (<USER MAIN>/<USER1>/<USER2>) to
which [SLOT SEL] is assigned and switch the target P2 card.
to
playback functions operate properly.
Inspecting the audio level automatic adjustment
1
Press the <AUDIO> button to display the [AUD02:INPUT]
screen of SmartUI.
2
Set the [IN] item in CH1/CH2 to [FRONT].
3
Set the [LVL] item in CH1/CH2 to [AUTO].