Panasonic AG-DVC80 User Manual
44
Item/
(display mode)
Description of settings
BEEP SOUND
(Camera)
(Camera)
CLOCK SET
(Camera)
(VCR)
(Camera)
(VCR)
For setting the internal calendar of the
camera recorder.
camera recorder.
HOUR METER
(Camera)
(VCR)
(Camera)
(VCR)
For indicating the total rotational time of the
cylinder head (5-digit display in 1-hour
increments).
cylinder head (5-digit display in 1-hour
increments).
TIME SHIFT
(Camera)
(VCR)
(Camera)
(VCR)
For adding the time which was set using
this item to the time of the internal calendar
(to compensate for time differences) for
display in the viewfinder and on the LCD
monitor. The clock time after the
compensation is also recorded on the tape.
+23h --- +1h, OFF, –1h --- –23h
(In 1-hour increments)
this item to the time of the internal calendar
(to compensate for time differences) for
display in the viewfinder and on the LCD
monitor. The clock time after the
compensation is also recorded on the tape.
+23h --- +1h, OFF, –1h --- –23h
(In 1-hour increments)
TAPE PROTECT
(Camera)
(Camera)
When the camera recorder is left on
standby for about 5 minutes in the shooting
pause mode, it is automatically set to the
tape protection mode. Which tape
protection mode is to be established is
selected using this item.
POWEROFF: The camera recorder’s power is
standby for about 5 minutes in the shooting
pause mode, it is automatically set to the
tape protection mode. Which tape
protection mode is to be established is
selected using this item.
POWEROFF: The camera recorder’s power is
set to the OFF mode.
STBY: The cylinder head is set to the stop
mode.
USER FILE
(Camera)
(VCR)
(Camera)
(VCR)
LOAD: The settings stored last in the user
file are loaded.
SAVE: The user file settings which have
been changed are saved.
INITIAL: The user file settings are restored
to the factory settings.
O
When the LOAD or INITIAL operation
has been performed, set the POWER
switch on the camera recorder to OFF
and then to ON again in order to enable
the settings.
has been performed, set the POWER
switch on the camera recorder to OFF
and then to ON again in order to enable
the settings.
Setting menus
The underlining indicates the factory setting.
OTHER FUNCTIONS screen
Item/
(display mode)
Description of settings
REMOTE
(Camera)
(VCR)
(Camera)
(VCR)
For setting the operations which are
performed using the accessory wireless
remote control unit. (See page 20 for the
remote control unit settings.)
VCR1: The operation performed by the
performed using the accessory wireless
remote control unit. (See page 20 for the
remote control unit settings.)
VCR1: The operation performed by the
remote control unit which has been set
to be used for VCR1 are accepted.
to be used for VCR1 are accepted.
VCR2: The operation performed by the
remote control unit which has been set
to be used for VCR2 are accepted.
to be used for VCR2 are accepted.
OFF: Operations performed by the remote
control unit are not accepted.
REC LAMP
(Camera)
(Camera)
For setting the lighting of the tally lamps.
OFF: The tally lamps do not light.
ON: Both the front and rear tally lamps light.
OFF: The tally lamps do not light.
ON: Both the front and rear tally lamps light.
For setting the beep tone to ON or OFF.
OFF
OFF
ON
When ON is selected as the setting, the
beep tone is sounded at the times given
below.
beep tone is sounded at the times given
below.
O
When the beep tone is sounded, the
audio signals from the output connectors
are muted, and the beep tone is output
instead.
audio signals from the output connectors
are muted, and the beep tone is output
instead.
[Beep tone sounds once]
O
When the POWER switch has been set
to ON
to ON
O
When shooting has commenced
[Beep tone sounds twice]
O
When shooting has been temporarily
stopped
stopped
[Beep tone sounds 10 times]
O
When the cassette tape has not been
inserted
inserted
O
When the cassette tape is in the
recording pause mode
recording pause mode
O
When condensation has formed inside
the camera recorder
the camera recorder
O
When a problem has occurred in the
camera recorder
camera recorder