Sony DVW-790WS/790WSP User Manual
7-1
DVW-790WS/709WS/707
DVW-790WSP/709WSP/707P P2V1
Section 7
Camera System Electrical Alignment
(Only for DVW-790WS/790WSP/709WS/709WSP)
7-1. General Information for Electrical
Adjustment
This section describes adjustment items that are required af-
ter this unit repair is repaired or its board is replaced.
ter this unit repair is repaired or its board is replaced.
7-1-1. Note for Adjustment
Before adjustment, set the main POWER switch to on and
the VTR switch to SAVE, then warm up the camcorder for
about 10 minutes.
Be sure to turn off the power before extending the plug-in
board using the extension board.
the VTR switch to SAVE, then warm up the camcorder for
about 10 minutes.
Be sure to turn off the power before extending the plug-in
board using the extension board.
Indication at the Top Right on the Viewfinder Screen
In adjustment on the setup menu, bars sometimes appear at
the top right on the viewfinder screen. The bars indicate the
current setting state and adjustable range for the selected item.
the top right on the viewfinder screen. The bars indicate the
current setting state and adjustable range for the selected item.
Screen Mode Setting
Sets the screen mode as follows before performing the
adjustment of the each page.
adjustment of the each page.
1.
Setup menu
PAGE : E14
PAGE : E14
*WIDE SCREEN
ITEM : 16:9/4:3 MODE
2.
Sets the screen mode as in the each page.
Screen mode
n
Some adjustment steps do not give the description of
screen mode. In this case, you can select either 16:9 or
4:3 mode during adjustment.
4:3
n
Some adjustment steps do not give the description of
screen mode. In this case, you can select either 16:9 or
4:3 mode during adjustment.
4:3
: Perform adjustment after switched to
the 4:3 mode.
16:9
: Perform adjustment after switched to
the 16:9 mode.
16:9 and 4:3 : Perform adjustment after switched first
to the 16:9 mode. Upon completion of
adjustment in the 16:9 mode, perform
adjustment in the 4:3 mode.
adjustment in the 16:9 mode, perform
adjustment in the 4:3 mode.
7-1-2. Equipment/Fixtures
. Oscilloscope
Tektronix 2465 or equivalent
. Waveform/Vector monitor
Tektronix 1780R/1751 or equivalent
. Color Monitor
Sony BVM-1410/1411P or equivalent
. Black and white monitor
. Pattern box (PTB-500, 90 - 240 Vac)
. Pattern box (PTB-500, 90 - 240 Vac)
J-6029-140-B
. Multiburst chart : J-6026-110-A
. Grayscale chart (4:3)
. Grayscale chart (4:3)
Transparent type : J-6026-130-B
Reflective type
Reflective type
: Commercially available on market
(Refer to Section 7-1-4.)
. Grayscale chart (16:9)
Transparent type : J-6394-080-A
7-1-3. Initial Switch Settings
Some adjustments of the Camera System Electrical
Alignment require the service mode of the setup menu to
Alignment require the service mode of the setup menu to
be used. Enter the service mode as follows.
Refer to Section 2 for details of the setup menu.
Refer to Section 2 for details of the setup menu.
1.
Turn off the POWER switch.
2.
Set switch S4-1 on the DCP-17 board to the ON
position.
position.
3.
Turn the POWER switch back on.
4.
Set the switch MENU ON/OFF/PAGE on the inside
panel to the ON position.
n
When any item is adjusted in the service mode, the values
When any item is adjusted in the service mode, the values
of the adjusted item in the engineer mode and user mode
are re-set to 0.
are re-set to 0.
7-9. VA Gain Adjustment
Note
16:9 mode
Screen mode
Example: