Sony F35 User Manual
33
Basic Settings with the Subdisplay
Chapt
er
3
B
a
s
ic
A
d
jus
tment
tment
s
and Se
tt
ing
s
s
To cancel a change on a setting
Without registering a change of a setting, press the
CANCEL/STATUS button. The question mark disappears,
and the original setting is restored.
CANCEL/STATUS button. The question mark disappears,
and the original setting is restored.
To terminate subdisplay operation
Press the VF MENU/DISPLAY button.
3-2-2 Shutter Settings
The electronic shutter of this camera can be adjusted, with
settings displayed in shutter angles, as with a film camera,
in addition to exposure time.
Two operation methods are available for the adjustment:
stepwise and continuous.
settings displayed in shutter angles, as with a film camera,
in addition to exposure time.
Two operation methods are available for the adjustment:
stepwise and continuous.
Step mode
Your frequently used shutter values (8 values at maximum)
can be registered, enabling stepwise selection of the
shutter values.
At shipment, the following values are registered:
Your frequently used shutter values (8 values at maximum)
can be registered, enabling stepwise selection of the
shutter values.
At shipment, the following values are registered:
The corresponding shutter speeds vary according to the
frame frequency and frame rate of the selected video
format. The step shutter values can be changed and re-
registered on the <SHUTTER ASSIGN> page of the
USER (OPERATION) menu or the <SHUTTER/FPS>
page of the USER (PAINT) menu.
frame frequency and frame rate of the selected video
format. The step shutter values can be changed and re-
registered on the <SHUTTER ASSIGN> page of the
USER (OPERATION) menu or the <SHUTTER/FPS>
page of the USER (PAINT) menu.
Continuous mode (ECS)
The shutter values can be continuously changed in a range
from 360.0 to 4.3 degrees.
To obtain your desired shutter value quickly, assign a value
nearest your desired one in Step mode, switch to
Continuous mode, then adjust the shutter value.
The shutter values can be continuously changed in a range
from 360.0 to 4.3 degrees.
To obtain your desired shutter value quickly, assign a value
nearest your desired one in Step mode, switch to
Continuous mode, then adjust the shutter value.
In a case where a remote control unit connected to the
REMOTE connector of the camera is used, adjustment in
Step mode is enabled with SHUTTER and adjustment in
Continuous mode is enabled with ECS (there is no need to
set to ECS ON). However, to display the shutter values on
REMOTE connector of the camera is used, adjustment in
Step mode is enabled with SHUTTER and adjustment in
Continuous mode is enabled with ECS (there is no need to
set to ECS ON). However, to display the shutter values on
the remote control unit correctly, upgrading of the version
is required.
is required.
For details, consult your local Sony representative.
Shutter setting page
To select a shutter value step by step
In Step mode, one of the registered shutter values (8 values
at maximum) can be selected, as follows:
at maximum) can be selected, as follows:
1
Move the cursor to the left of “S” at 1.
(Immediately after the shutter setting page is switched
to Setting Change mode, the cursor is always
displayed at the left of “S”.)
(Immediately after the shutter setting page is switched
to Setting Change mode, the cursor is always
displayed at the left of “S”.)
2
Display the shutter angle you wish to use at 2 by
turning the MENU SEL/ENTER dial.
turning the MENU SEL/ENTER dial.
The eight registered values for shutter angle will be
displayed one after another as the MENU SEL/
ENTER dial is turned.
displayed one after another as the MENU SEL/
ENTER dial is turned.
To select an arbitrary shutter value
To use a shutter value that is not registered as a step shutter
value, use Continuous mode.
value, use Continuous mode.
1
Press the SET button to move the cursor to the left of
“C” at 1.
“C” at 1.
2
Display the shutter angle you wish to use at 2 by
turning the MENU SEL/ENTER dial.
turning the MENU SEL/ENTER dial.
The shutter value changes continuously as the MENU
SEL/ENTER dial is turned.
SEL/ENTER dial is turned.
To change the units
You can change the displayed units for the shutter values
from shutter angle (deg) to speed (sec).
You can change the displayed units for the shutter values
from shutter angle (deg) to speed (sec).
1
Move the cursor to the left of
at 2.
2
Turn the MENU SEL/ENTER dial.
The display at 2 changes to the corresponding speed
value.
value.
STEP No.
Shutter angle
1
216.0º
2
180.0º
3
172.8º
4
150.0º
5
144.0º
6
90.0º
7
45.0º
8
22.5º
Note
S
C
3
6
0
.
0
O
N
2
4
F
P
S
C
M
P
:
O
F
F
1
2
3
4
5
S
C
1
/
2
4
.
0
0
O
N
?
2
4
F
P
S
C
M
P
:
O
F
F