TE Connectivity LAN Cat.6 S/FTP 1-0959385-1 User Manual

Product codes
1-0959385-1
Page of 5
108-93010 
 
 
Product 
Specification
 
 
14/Oct/2009 Rev E 
 
 
 
 
Cat 6 Shielded Patch cords
 
 
 
2009 Tyco Electronics AMP España, S.A.,  
Barcelona (Spain) 
All International Rights Reserved 
 
      1 of 5 
 
* Trademark 
| Indicates changes 
 
        LOC IK 
 
 
1. 
SCOPE 
 
1.1 
Content 
 
This  specification  describes  performance  and  material  requirements  and  tests  procedures  for  AMP 
NETCONNECT*  Cat  6  shielded  patch  cord  assemblies  used  to  connect  building  wiring  for  data  and  voice 
networking systems. 
 
1.2 
Qualification 
 
When  tests  are  performed  on  subject  product  line,  procedures  specified  in  Figure  1  shall  be  used.  All 
inspections shall be performed using applicable inspection plan and product drawing. 
 
2. 
APPLICABLE DOCUMENTS 
 
The  following  documents  form  a  part  of  this  specification  to  the  extent  specified  herein.  Unless  otherwise 
specified, the latest edition of the document applies. In the event of conflict between the requirements of this 
specification  and  the  customer  drawing  or  any  Tyco  Electronics  (TE)  documents  listed  below,  the  customer 
drawing  and  TE  documents  shall  take  precedence.  In  the  event  of  conflict  between  the  requirements  of  this 
specification and the industrial standards, this specification shall take precedence. 
 
2.1 
Tyco Electronics Documents  
 
 
 
A.  Relevant customer drawing 
 
B.  230-702: 
 
Design for environment standard – ‘Supplier Requirements for the  
Elimination of Hazardous Substances’ 
 
C.  108-93018: 
 
Product Specification - ‘Copper LAN cable’ 
 
2.2 
Industrial Standards: 
 
A.  ISO / IEC  11801 2
nd
 Edition: 
Generic Cabling for Customer Premises 
 
B.  Amendment 2 to ISO/IEC 11801 2
nd
 Edition. 
 
C.  EN 50173-1:   
Information Technology; Generic Cabling Systems 
 
D.  ANSI/TIA/EIA 568-B.2-1: 
Commercial Building Telecommunications Cabling Standard –  
Part 2: Balanced Twisted Pair Cabling Components – Addendum 1:  
Transmission Performance Specifications for 4-Pair 100Ohm  
Category 6 Cabling  
 
E.  IEC 61935-1:   
Generic cabling systems - Specification for the testing of balanced  
communication cabling in accordance with ISO/IEC 11801. Part 1: Installed  
cabling. 
 
F.  IEC 61935-2:   
Specification for the testing of balanced communication cabling in  
accordance with ISO/IEC 11801. Patch cords and work area cords. 
Test Specifications as indicated in Fig. 1. 
 
G.  IEC 61156-6:    
Multicore and symmetrical pair/quad cables for digital communications –  
Part 6: Symmetrical pair/quad cables with transmission characteristics up to  
1000MHz – Work area wiring – Sectional specification. 
 
H.  IEC 60603-7-5: 
Connectors for electronic equipment. Detail specification for 8-way, shielded,  
free  &  fixed  connectors,  for  data  transmission  with  frequencies  up  to  250 
MHz.