Panasonic SC-BTT350 User Manual

VQT2W23

∫ “Wired” connection

Follow the on-screen instructions to make your connection settings.
≥ When you experience problems (> right)

∫ “Wireless” connection

If you select “Wireless” and “Wireless LAN Adaptor is not 
connected.” is displayed, check that the Wireless LAN Adaptor 
is fully inserted. Alternatively, disconnect and reconnect it. If 
there is still no change in the display, consult your dealer for 
advice.

WPS (PUSH button):
If your Wireless router (Access point) 
supports WPS (PUSH button), you can 
easily perform the settings by pressing 
WPS button on it.
WPS (Wi-Fi Protected Setup) is a 
standard that facilitates settings relating 
to the connection and security of 
wireless LAN devices.
1 Press WPS button or corresponding button of Wireless 

router (Access point) until the lamp starts flashing.
≥ For details, refer to the operating instruction of Wireless 

router (Access point).

2 Press [OK].

Search for access point:
Available Wireless routers (Access points) are searched and 
listed. You can select the one to use from the list.

1 Press [

3, 4] to select SSID*

2

 of Wireless router (Access 

point) you want to connect with. Then press [OPTION] to 
show information of the selected router, make a note of the 
authentication and encryption type.

≥ If you can not find the SSID*

2

, select “Search again”.

2 Press [RETURN] and then press [OK].

Then select an item on the following screen which 
corresponds to the authentication type noted down in step 
1 (> left).

Follow the on-screen instructions to make the settings.
≥ Input your encryption key code in “Encryption Key” 

supplied with your Wireless router (Access point).

*1

Wi-Fi Protected Setup-compatible Wireless router (Access point) may 
have the mark.

*2

An SSID (Service Set IDentification) is a name used by wireless LAN to 
identify a particular network. Transmission is possible if the SSID 
matches for both devices.

Network Easy Setting

OK

RETURN

Network Easy Setting (Connection Test)

Wired

Wireless

Select a connection mode. 

 Current setting 

:  Wired

 LAN cable connection:

 Connect a LAN cable to the unit and select “Wired”.

Wireless LAN connection:

 Connect the Wireless LAN Adaptor (DY-WL10) to the USB
 port and select “Wireless”.

Access Point Connection Setting

Select a connection method for access to 
Wireless LAN.
Please refer to the operating instructions of 
the access point about connection methods.

WPS (PUSH button)

Search for access point

1

e.g.,

OK

Access Point Connection Setting

Reception

Select an access point to connect with.
To search for access point again, please 
select "Search again" below.

SSID

XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX
XXXXXXXXXX

Search again

SSID
Wireless type
Authentication type
Encryption type

:XXXXXXXXXXXXXXX
:802.11n/g/b (2.4GHz)
:WPA-PSK
:AES

When you experience 
problems with settings

A conflict with other 
devices occurred.

≥ Please wait a few moments, 

and then try again.

A time out error occurred.

≥ Setting of the Wireless 

router (Access point) for 
MAC Address etc.

≥ The signal may be weak. 

Using the USB extension 
cable supplied with the 
Wireless LAN Adaptor, 
adjust the position of the 
Wireless LAN Adaptor.

≥ The SSID and the 

encryption key of the 
Wireless router (Access 
point).

≥ Please wait a few moments, 

and then try again.

An authentication error or a 
time out error occurred.

A device error occurred.

≥ Connection of Wireless LAN 

Adaptor
If there is no improvement in 
symptom, consult your 
dealer.

Access Point Connection Setting

WPA2-PSK (AES/TKIP)

WPA-PSK (AES/TKIP)

Open/Shared Key (WEP)

Open system

Select authentication type.

 

OK

Access Point Connection Setting

Yes

No

Failed to connect to the access point.

A conflict with other devices occurred.

Do you wish to setup Access Point 
Connection Setting again ?

SCBTT755_350EBGN_VQT2W23.book  22 ページ  ２０１０年７月８日　木曜日　午後６時５３分