Panasonic DMP-BD45 User Manual

VQT2H86

≥ Refer to the operating instructions of the hub or router.
≥ You can perform this setup anytime by selecting “Network Easy Setting” in 

the Setup menu. (

>

28)

≥ You can redo these settings individually using “Network Settings”. (

>

28)

≥ Do not use this device to connect to any wireless network for which you 

do not have usage rights.
During automatic searches in a wireless network environment, wireless 

networks (SSID*) for which you do not have usage rights may be 

displayed; however, using these networks may be regarded as illegal 

access.

≥ After performing network settings on this unit, the settings (encryption 

level, etc.) of the Wireless router (Access point) might change. When you 
have trouble getting online on your PC, perform the network settings on 
your PC in accordance with the settings of Wireless router (Access point).

* An SSID (Service Set IDentification) is a name used by wireless LAN to 

identify a particular network. Transmission is possible if the SSID 

matches for both devices.

When you experience 
problems with settings

A conflict with another 
device occurred.

≥ Please wait a few moments, 

and then try again.

A time out error occurred.

≥ Setting of the Wireless 

router (Access point) for 
MAC Address etc.

≥ The signal may be weak. 

Using the USB extension 
cable included with the 
Wireless LAN Adaptor, 
adjust the position of the 
Wireless LAN Adaptor.

≥ The SSID* and the 

encryption key of the 
Wireless router (Access 
point).

≥ Please wait a few moments, 

and then try again.

An authentication error or a 
time out error occurred.

A device error occurred.

≥ Connection of Wireless LAN 

Adaptor
If there is no improvement in 
symptom, contact our 
Customer Service Center.

1. LAN cable connection or 
Connection to access point

: Fail

≥ Connection of 

the LAN 
cables (> 10)

2. IP address setting

: Fail

3. Connection to gateway

: Fail

OK

Access Point Connection Setting

Failed to connect to the access point.

A conflict with another device occurred.

Do you want to configure Access Point Connection
Setting again ?

Yes

No

OK

Network Easy Setting (Connection Check)

Yes

No

Complete.

1. LAN cable connection         

2. IP address setting
3. Connection to gateway

LAN cable is not connected.

Please check the connection.

Select “Yes” and press [OK] to check network
connection again. Select “No” and press [OK]

to finish Network Easy Setting.

: Fail

: Fail
: Fail

1. LAN cable connection or 
Connection to access point

: Pass

≥ Connection 

and settings 
of the hub 
and router

≥ Settings of 

“IP Address/
DNS 
Settings” 
(> 28)

2. IP address setting

: Fail

3. Connection to gateway

: Fail

1. LAN cable connection or 
Connection to access point

: Pass

2. IP address setting

: Pass

3. Connection to gateway

: Fail

Cannot find the server.
(Error code: B019)

≥ “Primary DNS” and “Secondary 

DNS” settings of “IP Address/
DNS Settings” (> 28)

Failed to connect to 
the server.
(Error code: B020)

≥ The server may be busy or the 

service may have been 
suspended. Please wait a few 
moments, and then try again.

≥ Settings of “Proxy Server 

Settings” (> 28) and the router

OK

Network Easy Setting (Internet Connection Check)

Complete.

- Connection to the Internet       :   Fail(Error code: B019)

Failed the connection test.

Cannot find the server.(Error code: B019)

Please refer to the operating instructions for the cause
of the error and the solution for it.

Press [OK].

VQT2H86~Body_eng.fm  13 ページ  ２０１０年１月１８日　月曜日　午前１０時２１分