Panasonic DMP-BDT270 User Manual
- 29 -
You have forgotten your ratings password.
You want to cancel the ratings level.
¾
You want to cancel the ratings level.
¾
The ratings level returns to the factory
defaults.
defaults.
1 Turn the unit on.
2 Press and hold [OK], the yellow button and
2 Press and hold [OK], the yellow button and
the blue button on the remote control at the
same time for more than 5 seconds.
– POWER LED starts to flash, and “00 RET”
same time for more than 5 seconds.
– POWER LED starts to flash, and “00 RET”
is displayed on the screen.
3 Press [
1] (right) repeatedly on the remote
control until “03 VL” is displayed on the screen.
4 Press [OK].
The TV screen turns black.
¾
¾
In the following cases, HDMI authentication
takes place and a black screen is displayed:
–
takes place and a black screen is displayed:
–
[BDT270]
When “24p(4K)/24p Output” is set to
“24p(4K)” or “24p”.
–
[BD93]
When “24p Output” is set to “On”.
–
[BDT270]
When the display is switched
between 2D and 3D images.
This unit does not recognize the USB
connection correctly.
¾
connection correctly.
¾
Disconnect and re-connect the USB cable. If
it still does not recognize the connection, turn
this unit off and on again.
it still does not recognize the connection, turn
this unit off and on again.
¾
USB devices may not be recognized by this
unit when connected using the following :
– a USB hub
– a USB extension cable
unit when connected using the following :
– a USB hub
– a USB extension cable
¾
If you connect USB HDD to this unit, use the
USB cable that is supplied with the HDD.
USB cable that is supplied with the HDD.
The images from this unit do not appear on
the TV.
Picture is distorted.
¾
the TV.
Picture is distorted.
¾
An incorrect resolution is selected in “HDMI
Resolution”. Reset the setting as follows:
Resolution”. Reset the setting as follows:
1 Turn the unit on.
2 Press and hold [OK], the yellow button and
2 Press and hold [OK], the yellow button and
the blue button on the remote control at the
same time for more than 5 seconds.
– POWER LED starts to flash.
same time for more than 5 seconds.
– POWER LED starts to flash.
3 Press [8] and the blue button on the remote
control at the same time for more than
5 seconds.
Set the item again. (> 23)
– When Dolby Digital Plus, Dolby TrueHD,
5 seconds.
Set the item again. (> 23)
– When Dolby Digital Plus, Dolby TrueHD,
and DTS-HD
®
audio are not output properly,
select “Yes” in “Restore Default Settings”
(> 27) and make proper settings.
(> 27) and make proper settings.
¾
[BDT270]
When “3D BD-Video Playback” in the
Setup menu is set to “Auto”, images may not
be output depending on the connection
method. After removing the disc from this unit,
select “Set before play” in the Setup menu,
and select “2D Playback” in the setup screen
displayed when playing 3D discs. (> 25)
be output depending on the connection
method. After removing the disc from this unit,
select “Set before play” in the Setup menu,
and select “2D Playback” in the setup screen
displayed when playing 3D discs. (> 25)
¾
[BDT270]
When outputting in 24p (4K), images
may be distorted depending on the HDMI
cable. Use an HDMI cable that supports 4K
output.
cable. Use an HDMI cable that supports 4K
output.
Video is not output in high-definition.
¾
¾
Confirm that “HDMI Resolution” in the Setup
menu is set properly. (> 23)
menu is set properly. (> 23)
[BDT270]
3D video is not output.
¾
¾
Connect to a full high-definition TV.
¾
¾
Are the settings on this unit and the TV
correct? (> 17)
correct? (> 17)
¾
Is the amplifier/receiver that is connected
between this unit and TV on?
between this unit and TV on?
¾
Depending on the connected TV, the video
being played back might switch to 2D video
due to changes in resolution etc. Check the
3D setting on the TV.
being played back might switch to 2D video
due to changes in resolution etc. Check the
3D setting on the TV.
Picture