Ikelite GZ-MG-360 Leaflet
I
I N
N SS TT AA LL LL AA TT II O
O N
N
CCAAM
MEERRAA TTRRAAYY
________________________________________________________________________________________________________________________
The camera mounts to the tray, which extends from the back plate of the housing.
D
DO
O N
NO
OTT remove the tray from the back plate. The camera strap MUST be positioned
underneath the camera tray as noted below.
1. Remove camera strap from front loop on the camera.
2. Open the camera LCD screen.
3. Place the camera against the stabilizing pins on the tray. Secure camera with
2. Open the camera LCD screen.
3. Place the camera against the stabilizing pins on the tray. Secure camera with
the tripod mounting bolt. The camera should fit easily on the tray and should
be parallel with the sides of the tray.
4. Loop the camera strap underneath the camera tray and attach the open end
of the strap around the spring pin on the housing back.
5. Press the LCD screen against the shade on the back.
RReem
moovvee tthhee ccaam
meerraa ssttrraapp ffrroom
m tthhee ffrroonntt lloooopp oonn tthhee ccaam
meerraa..
LLoooopp tthhee ccaam
meerraa ssttrraapp uunnddeerrnneeaatthh tthhee ccaam
meerraa ttrraayy aanndd aattttaacchh tthhee ooppeenn eenndd
ooff tthhee ssttrraapp aarroouunndd tthhee sspprriinngg ppiinn oonn tthhee hhoouussiinngg bbaacckk w
wiitthh tthhee ffllaapp ooppeenn..
Camera
Camera Strap
Spring Pin
Mounting Tray
Front Loop
Camera
Spring Pin
Front Loop
Camera Strap
Mounting
Tray
Tray
I
I N
N SS TT AA LL LL AA TT II O
O N
N cc oo nn tt ii nn uu ee dd
IIN
NSSEERRTTIIN
NGG TTH
HEE CCAAM
MEERRAA
__________________________________________________________________________________________________
Check that the clean o-ring is properly positioned on the lip of the clear back plate.
Place the lid snaps in the open position.
Once the camera is mounted to the tray and the camera strap is secured underneath
the tray, pull the housing controls out to provide clearance for the camera. Align the
back plate with the clear housing and slowly place the back plate against the housing.
D
DO
O N
NO
OTT force this installation; if the controls are out of the way and everything
is lined up properly, the camera and tray will fit easily inside. Make certain that the tray
is completely in the housing. The front should be flat against the housing and NOT tilted
on one side.
H
HO
OU
USSIIN
NGG CCO
ON
NTTRRO
OLLSS
__________________________________________________________________________________________________________
Slide the housing controls back in place making sure they properly align with the
camera functions. Fasten the opposite lid snaps at the same time--D
DO
O N
NO
OTT fasten one
at a time.
Operate each control to see how it works with the camera. Some controls such as
start/stop will be used frequently. Other controls may seldom be utilized. Refer to your
camera owners manual for the proper function of each camera control. Look thru the
back to be sure that you can see into the viewfinder.
When using the housing controls, especially the start/stop, D
DO
O N
NO
OTT use excessive
force because you could damage the camera.
CCAAU
UTTIIO
ON
N
Remove the lens cap and cord from the camera. Otherwise, the cord may
interfere with the housing seal.
If the housing controls are not properly positioned, they could interfere with the housing seal.
IIKKEELLIITTEE U
UN
ND
DEERRW
WAATTEERR SSYYSSTTEEM
MSS
50 West 33rd Street • PO Box 88100 • Indianapolis, IN 46208 USA • 317.923.4523
Email: ikelite@ikelite.com
•
www.ikelite.com
6014.10-01-0608