Renesas rl78 User Manual
RL78/G1A
CHAPTER 6 TIMER ARRAY UNIT
R01UH0305EJ0200 Rev.2.00
203
Jul 04, 2013
Figure 6-11. Format of Timer Mode Register mn (TMRmn) (2/4)
Address: F0190H, F0191H (TMR00) to F019EH, F019FH (TMR07) After reset: 0000H R/W
Symbol 15
14
13
12
11
10
9 8 7 6 5 4 3 2 1 0
TMRmn
(n = 2, 4, 6 )
CKS
mn1
CKS
mn0
0
CCS
mn
MAST
ERmn
STS
mn2
STS
mn1
STS
mn0
CIS
mn1
CIS
mn0
0 0
MD
mn3
MD
mn2
MD
mn1
MD
mn0
Symbol 15
14
13
12
11
10
9 8 7 6 5 4 3 2 1 0
TMRmn
(n = 1, 3)
CKS
mn1
CKS
mn0
0
CCS
mn
SPLIT
mn
STS
mn2
STS
mn1
STS
mn0
CIS
mn1
CIS
mn0
0 0
MD
mn3
MD
mn2
MD
mn1
MD
mn0
Symbol 15
14
13
12
11
10
9 8 7 6 5 4 3 2 1 0
TMRmn
(n = 0, 5, 7)
CKS
mn1
CKS
mn0
0
CCS
mn
0
Note
STS
mn2
STS
mn1
STS
mn0
CIS
mn1
CIS
mn0
0 0
MD
mn3
MD
mn2
MD
mn1
MD
mn0
(Bit 11 of TMRmn (n = 2, 4, 6))
MAS
TER
mn
Selection between using channel n independently or
simultaneously with another channel(as a slave or master)
0
Operates in independent channel operation function or as slave channel in simultaneous channel operation
function.
1
Operates as master channel in simultaneous channel operation function.
Only the channel 2, 4, 6 can be set as a master channel (MASTERmn = 1).
Be sure to use channel 0, 5, 7 are fixed to 0 (Regardless of the bit setting, channel 0 operates as master, because it
is the highest channel).
Clear the MASTERmn bit to 0 for a channel that is used with the independent channel operation function.
(Bit 11 of TMRmn (n = 1, 3))
SPLI
Tmn
Selection of 8 or 16-bit timer operation for channels 1 and 3
0
Operates as 16-bit timer.
(Operates in independent channel operation function or as slave channel in simultaneous channel operation
function.)
1
Operates as 8-bit timer.
STS
mn2
STS
mn1
STS
mn0
Setting of start trigger or capture trigger of channel n
0
0
0
Only software trigger start is valid (other trigger sources are unselected).
0
0
1
Valid edge of the TImn pin input is used as both the start trigger and capture trigger.
0
1
0
Both the edges of the TImn pin input are used as a start trigger and a capture trigger.
1 0 0
Interrupt signal of the master channel is used (when the channel is used as a slave channel
with the simultaneous channel operation function).
Other than above
Setting prohibited
Note Bit 11 is fixed at 0 of read only, write is ignored.
Remark m: Unit number (m = 0), n: Channel number (n = 0 to 7 (however, timer input pin (TImn), timer output pin
(TOmn) : n = 0, 1, 3 to 7))