DMP Electronics XR200A Leaflet

Resistor

DMP Model 309

Battery Only Restart CR7

J16

Command
Processor

Reset

ZONE EXPANDER

Model 714

15mAat 12 VDC

Models 714-8, 714-16

20mA @ 12 VDC

RED

BLACK

22 GA. MIN

GREEN

22 GA. MIN

BLACK

22 GA. MIN

YELLOW

22 GA. MIN

RED

Protective
Earth Ground

Yellow

Red

Green

Black

16 to 18 gauge wire

DMP Model 310

Smoke

Detector

Power
Supervision
Relay

Output Header J2

J11

J12

Ground Start Relay
Use Model 305

DD, MPX
Selection

Rear Tamper

Front Tamper

Tamper Header

ZONE 5

ZONE 1

ZONE 2

ZONE 3

ZONE 4

LT-0468 (12/99)

1
9

-B

BELL

GND

SMK

GND

RED

YEL

GRN

BLK

GND

Z9 +

Z9 -

Z10 +

Z10 -

ZONE 6

ZONE 7

ZONE 8

3.3k

Resistor

DMP Model 309

Phone Jack Connector

Relay Output 1
Use Model 305

Relay Output 2
Use Model 305

J6 Interface Connector

ZONE 9

ZONE 10

Red

Form C Relays

Output 1

N/C

Violet

Output 1

Com

Gray

Output 1

N/O

Orange

Output 2

N/C

Violet

Output 2

Com

Gray

Output 2

N/O

Orange

Voltage Outputs

Output 3

White/Orange

Output 4

White/Yellow

Output 5

White/Green

Output 6

White/Blue

Output 7

White/Violet

Output 8

White/Gray

Output 9

White

Output 10

White/Black

Ground

Black

J2 Output color code for

Model 430 Output Harness

A R M

D I S A R M

Auxiliary Power

Total current 1.0 Amps
combined from Terminals
7, 11, 26, & 28.

See the XR200A Installation Guide for a
list of approved 2-wire smoke detectors
for zones 9 and 10 and 715 Zone
Expanders.

ZONE EXPANDER

Model 715

25mA @ 12 VDC

Models 715-8, 715-16

20mA @ 12 VDC

ZONE

EXPANDER

Model 711/711E

12mA at

12 VDC

Wiring on terminals
5 through 22 must
exit to the right and
maintain a 1/4"
separation from the
AC and battery
positive wiring.

= Supervised Circuit

Heat detectors,
pull stations, or
any other shorting
devices can be
connected to
zones 9 and 10.

Keypads
Model 670, 770, and 771
125mA at 8 to 16 VDC.

Model 690
90mA at 8 to 16 VDC.

Model 790 and 791
100mA at 8 to 16 VDC.

Model 793
130 mA at 8 to 16 VDC.

MODEL XR200A WIRING DIAGRAM

Refer to the XR200A Installation Guide (LT-0482) for a complete description of wiring connections.
Refer to the XR200 Programming Manual (LT-0196) for complete programming instructions.

Maximum AC wire distance
With 16 gauge wire: 70 feet
With 18 guage wire: 40 feet

Bell
12 VDC nominal
Total current 1.5 Amps max.

Keyswitch Arming
Can be connected to any loop.

Secondary Power Supply
1.2 Amps max. charging current.
Use only 12 VDC rechargable
batteries. DMP Model 367.
Replace every 3 to 5 years.

Refer to LT-0164 for a list of approved 4-wire
smoke detectors and power supervision relays.

Tamper protection
when required for
Model 350A Attack
Resistant Enclosure.

Answering
Machine
Bypass Relay
Use Model 305

In all applications where more than one wire is
under a terminal, the wire must be cut and not
looped around the screw terminal.

AC wiring must be in conduit and exit out the left
side of the enclosure.

Bell

3.3k

s
s

Zones 9 and 10 and
Model 715 compatibility
identifier: A
Maximum operating
range:
8.8 VDC to 14.2 VDC.

Lithium
Battery

CAUTION

Danger of explosion if lithium battery is incorrectly replaced.
Replace only with DMP part number BT-0005 or equivalent
type. When discharged, disposal of used lithium battery is
non- hazardous per USEPA criteria. Disposal according to
local, state, and federal waste regulations.

Primary Power
16VAC
40 - 100 VA

WARNING!
Installation to be
performed by
authorized personnel.

ACN 087 480 279

Downloaded from:

http://www.guardianalarms.net