Nissan Home Security System Leaflet

NISSAN INTEGRATED HOMELINK

TRANSCEIVER

(If so equipped)

WARNING: During the set up procedure, the device you are programming

(e.g., garage door, electric gate, entry door, etc.) will be activated. To avoid injury,
make sure that people and objects are clear of all doors and gates during
programming. Also, your vehicle’s engine should be turned off while programming
the HomeLink

Transceiver. Refer to your Owner’s Manual for complete details.

PROGRAMMING YOUR NISSAN INTEGRATED HOMELINK

TRANSCEIVER

(Mirror controls shown; same steps apply for console and visor controls)

To program your HomeLink

Transceiver to operate a garage door, gate,

home/office lighting, or entry door opener, you will need to be in the same location
as the device.

Note: Garage door openers manufactured after 1996 have “rolling code
protection.” To program a garage door opener equipped with “rolling code
protection,” you will need to be able to reach the motor of the garage door opener.
This is where the “smart” or “learn” program button is located. For this step (#5),
you may need a ladder.

1. To begin, press and hold the two outer
HomeLink

buttons to clear the memory.

Hold down both buttons until the indicator
light blinks slowly (this should take about 20
seconds). Release the buttons.

2. Position the hand-held transmitter for the
device you would like to program 1-3 inches
away from the HomeLink

buttons.

3. Using both hands, simultaneously press and
hold down the hand-held transmitter button
and the HomeLink

button you want to

program

. DO NOT release these buttons

until Step 4 has been completed.

4. Continue to hold down both buttons until the
HomeLink

indicator light flashes slowly then

rapidly (this could take up to 90 seconds). The
rapidly flashing light indicates successful
programming, and at this point you can release
the buttons. Your HomeLink

button should

now be programmed.

If the HomeLink

Indicator Light Blinks Rapidly

for Two Seconds and then Illuminates Solid…
HomeLink

has picked up a “rolling code” garage

door opener signal. You will need to perform the
following steps to “train” HomeLink

to complete

programming. You may require a ladder and
another person for convenience.

5. To activate the “training mode,” press and
release the “smart” or “learn” button located
on the motor of the garage door opener. This
button is usually near the antenna wire that
hangs down from the motor. If the wire
originates from under a light lens, you will
need to remove the lens to access the button.

Note: Once you have pressed and released

the button on the motor, you will have

seconds

to perform the next step. For convenience, use the help of a second

person.

6. Within 30 seconds of pressing the button on the motor, firmly press the
HomeLink

button you’ve just tried to program, holding it down for two seconds

and then releasing it. Repeat the “press/hold/release” sequence up to three
times. When the indicator light illuminates solid/continuous, “training” is
complete and your HomeLink button should now be programmed.

To Program Remaining Homelink

Buttons: Perform Steps 2-4 (and 5 and 6, if

needed) again.

DO NOT

perform Step 1 unless you want to clear all previously

programmed HomeLink

buttons.

To Activate Programmed Devices: Press and hold the programmed HomeLink

button, releasing it when the device begins to activate.

If you have any questions or are having difficulty programming your

HomeLink

buttons,

please refer to the

HomeLink

Web site at www.HomeLink.com or call 1-800-355-3515.

Indicator light changes from a
slow blink to a rapid flash

Step 3-4

“Smart” or
“learn” button

Step 5

To complete
training, firmly press
and release the
programmed button

Step 6

Red indicator
light

Step 1

Hold end of hand-held
transmitter 1-3”
away from HomeLink

Step 2

Fold

her

MIRROR

VISOR

CONSOLE