Panasonic AW-HE130K User Manual
Service switch settings
SW1 to SW3 (camera address setting switches)
Configure the camera address.
Set this to AUTO under normal circumstances. When cameras are set
to AUTO, addresses will be assigned to the cameras automatically
in response operation from the controller in the order in which the
cameras were connected.
To manually configure the address, set the switches as follows.
Address
AUTO
1
2
3
4
5
6
7
SW1
OFF
ON
OFF
ON
OFF
ON
OFF
ON
SW2
OFF
ON
ON
OFF
OFF
ON
ON
OFF
SW3
OFF
ON
ON
ON
ON
OFF
OFF
OFF
SW4 (communication format selection switch)
Selects the communication format.
When this is set to ON, standard serial communication is enabled.
When this is set to OFF, Panasonic's proprietary serial
communication is enabled.
SW5 (maintenance switch)
Fixed at OFF.
Do not change this switch setting.
SW6 (infrared output switch)
When this is set to ON, infrared output is enabled. The signal received
via the remote control sensor is output from pins 7 and 8 of the <RS-
232C IN> connector.
Signal output is disabled when this is set to OFF.
SW7 (communication baud rate switch)
When this is set to ON, the baud rate is 38400 bps.
When this is set to OFF, the baud rate is 9600 bps.
SW8 (communication connector switch)
When this is set to ON, the RS-422 is enabled.
When this is set to OFF, the RS-232C is enabled.
Simultaneous output conditions for each video
format
z
SDI/HDMI/VIDEO output
Format
SDI
output
HDMI
output
VIDEO
output
HD/SDI
1080/59.94p
1080/50p
1080/59.94i
1080/50i
1080/29.97psF
1080/25psF
1080/23.98psF
1080/29.97p
1080/25p
1080/23.98p
720/59.94p
720/50p
SD/SDI
480/59.94p
576/50p
480/59.94i
*
1
576/50i
*
1
*
1
480/59.94i and 576/50i is output to the VIDEO output regardless of
the format setting.
z
IP video transmission output (1-/multi-channel display)
1-channel display
Resolution
1920×1080 / 1280×720 / 640×360 / 320×180 / 160×90
(non-dependent on SYS format)
Frame
rate
60Hz
1 fps/2 fps/3 fps/5 fps/6 fps/10 fps/15 fps/30 fps/
60 fps
*
1
50Hz
1 fps/2 fps/5 fps/10 fps/12.5 fps/25 fps/50 fps
*
2
*
1
60 fps only during H.264 transmission and 1920×1080 or 1280×720
resolution
*
2
50 fps only during H.264 transmission and 1920×1080 or 1280×720
resolution
Multi-channel display
Setting
H.264 CH1
H.264 CH2 H.264 CH3/
CH4
JPEG CH1/
CH2/CH3
*
3
Resolution
1920×1080 /
1280×720
1920×1080 /
1280×720 /
640×360 /
320×180 /
160×90
1280×720 /
640×360 /
320×180 /
160×90
1920×1080 /
1280×720 /
640×360 /
320×180 /
160×90
Frame
rate
60Hz
60fps
5 fps/15 fps/
30 fps
5 fps/15 fps/
30 fps
1 fps/2 fps/
3 fps/5 fps/
6 fps/10 fps/
15 fps/30 fps
50Hz
50 fps
5 fps/
12.5 fps/
25 fps
5 fps/
12.5 fps/
25 fps
1 fps/2 fps/
5 fps/10 fps/
12.5 fps/
25 fps
*
3
Different resolutions must be specified for JPEG CH1 / CH2 / CH3.
20
Parts and their functions (continued)
21