Bosch ICP-CC488 User Manual
ICP-CC488 | Installation Guide | 3.0
System Operations
EN | 16
Bosch Security Systems, Inc. | 12/08 | F01U089457-02
The indicators for any zones that are programmed to
be automatically isolated in STAY Mode 2 flash until
the Exit Time expires. At the end of Exit Time, the
zone indicators are extinguished and the codepad
sounds one short beep.
be automatically isolated in STAY Mode 2 flash until
the Exit Time expires. At the end of Exit Time, the
zone indicators are extinguished and the codepad
sounds one short beep.
If a zone is not sealed at the end of Exit Time, the
zone is automatically isolated and is lit constantly on
the remote codepad. The zone becomes an active
part of the system again as soon as it is resealed. For
example, if a window is open when Exit Time
expires, the window does not become an active part
of the system until it is closed. Opening the window
after Exit Time expires causes an alarm.
zone is automatically isolated and is lit constantly on
the remote codepad. The zone becomes an active
part of the system again as soon as it is resealed. For
example, if a window is open when Exit Time
expires, the window does not become an active part
of the system until it is closed. Opening the window
after Exit Time expires causes an alarm.
Forced Arming
Arming the system when a zone is not sealed is
known as forced arming. Refer to Section 14.3.7 Zone
Options 2 on page 63 to enable forced arming for
each zone.
known as forced arming. Refer to Section 14.3.7 Zone
Options 2 on page 63 to enable forced arming for
each zone.
If the STAY indicator does not light and a long beep
sounds when attempting to arm the system, forced
arming is not permitted. If this is the case, you must
seal all zones or manually isolate them before you
can arm the system.
sounds when attempting to arm the system, forced
arming is not permitted. If this is the case, you must
seal all zones or manually isolate them before you
can arm the system.
3.6
Disarming the System from STAY
Mode 2
Mode 2
There are two methods to disarm the system from
STAY Mode 2. You can always use the first method.
You can use method two only if Option 4 is enabled
in Location 497 (refer to Section 18.6 Consumer
Options 2 on page 83).
STAY Mode 2. You can always use the first method.
You can use method two only if Option 4 is enabled
in Location 497 (refer to Section 18.6 Consumer
Options 2 on page 83).
To disarm the system from STAY Mode 2
(method one):
1. Enter your code and press [STAY].
2. Two beeps sound and the STAY indicator is
(method one):
1. Enter your code and press [STAY].
2. Two beeps sound and the STAY indicator is
extinguished. The system is now disarmed.
To disarm the system from STAY Mode 2
(method two):
(method two):
A flashing zone indicator represents a previous alarm
in that zone. If this is the case, a valid User Code is
required to disarm the system using method one. To
enable method two, Option 4 in Location 497 must
be enabled (refer to Section 18.6 Consumer Options 2 on
page 83).
1. Press and hold [0].
2. When two beeps sound, release the button.
in that zone. If this is the case, a valid User Code is
required to disarm the system using method one. To
enable method two, Option 4 in Location 497 must
be enabled (refer to Section 18.6 Consumer Options 2 on
page 83).
1. Press and hold [0].
2. When two beeps sound, release the button.
The STAY indicator is extinguished and the
system is disarmed.
system is disarmed.
Single button disarming from STAY
Mode 2 reports as User Code16.
Mode 2 reports as User Code16.
3.7
Codepad Duress Alarm
Figure 6: ICP-CP500PW LED Codepad
Showing Audible Alarm Buttons
A codepad Duress Alarm is used as a silent holdup
alarm when 9 is added to the end of a valid User
Code being used to disarm the system. If a User
Code has a priority level that allows arming only,
that User Code can transmit a Duress Alarm when
the system is armed.
alarm when 9 is added to the end of a valid User
Code being used to disarm the system. If a User
Code has a priority level that allows arming only,
that User Code can transmit a Duress Alarm when
the system is armed.
A Duress Alarm (Contact ID Event Code 121) is
useful only if your system reports to a monitoring
station or pocket pager because domestic reporting
format cannot decipher the type of alarm that
occurred. You can disable the codepad Duress Alarm
Report by programming 0 in Location 394 (refer to
Section 15.15 Codepad Duress Report). You can select
Option 2 in Location 498 to use 3 instead of 9 to
activate a Duress Alarm (refer to Section 18.7
Consumer Options 3 on page 83).
useful only if your system reports to a monitoring
station or pocket pager because domestic reporting
format cannot decipher the type of alarm that
occurred. You can disable the codepad Duress Alarm
Report by programming 0 in Location 394 (refer to
Section 15.15 Codepad Duress Report). You can select
Option 2 in Location 498 to use 3 instead of 9 to
activate a Duress Alarm (refer to Section 18.7
Consumer Options 3 on page 83).
3.8 Codepad
Panic
Alarm
An audible codepad Panic Alarm activates when a
user presses either [1] and [3] or [STAY] and
[AWAY] simultaneously.
user presses either [1] and [3] or [STAY] and
[AWAY] simultaneously.
Select Option 1 in Location 493 to program the
codepad Panic Alarm as silent (refer to Section 18.2
System Options 2 on page 81). To disable the codepad
Panic Alarm Report, program Locations 405 and 406
to 0 (refer to Section 15.16 Codepad Panic Report on
page 66). A codepad Panic Alarm transmits Contact
ID Event Code 120 if the system reports to a base
station receiver.
codepad Panic Alarm as silent (refer to Section 18.2
System Options 2 on page 81). To disable the codepad
Panic Alarm Report, program Locations 405 and 406
to 0 (refer to Section 15.16 Codepad Panic Report on
page 66). A codepad Panic Alarm transmits Contact
ID Event Code 120 if the system reports to a base
station receiver.