Essick Air SAS10012 User Manual

110526

4

This warranty is extended to the original purchaser of an evaporative cooler installed and used under normal conditions.  It does not cover damages in-
curred through accident, neglect, or abuse by the owner.  We do not authorize any person or representative to assume for us any other or different liability 
in connection with this product.

Lifetime Limited Coverage on water reservoir against any leakage due to defects in material.  From date of purchase, if any original component part fails 
due to defect in material or factory workmanship only, we will provide the replacement part as follows:

 

One year on the cabinet components.

 

Two years on the evaporative media.

 

We are not responsible for any incidental or consequential damage resulting from any malfunction.

We are not responsible for any damage received from the use of water softeners, chemicals, de-scale material, plastic wrap, or if a motor of a higher 
horsepower than what is shown on the serial plate is used in the unit.

We are not responsible for the cost of service calls to diagnose cause of trouble, or labor charge to repair and/or replace parts.

Contact the Dealer where you purchased the evaporative cooler.  If for any reason you are not satisfi ed with the response from the dealer, contact the 
Customer Service Department:  5800 Murray Street, Little Rock, Arkansas 72209.  1-800-643-8341.  E-mail: info@championcooler.com,  Web: www.
championcooler.com.

Failure to 
start or no air 
delivery

Inadequate 
air delivery 
with cooler 
running

Musty or 
unpleasant 
odor

1. No electrical power 

to unit

 • Fuse blown
  •  Circuit breaker tripped
2. Belt too loose or tight
3. Motor overheated

  •  Belt too tight
  •  Blower bearings dry

  •  Motor bearings dry
  •  Motor pulley diameter 

too large

4. Motor locked

1. Insuffi cient air exhaust

2. Belt too loose

3. Pads plugged
4. Insuffi cient water fl ow 

over pads

1. Stale or stagnate water 

in cooler

2. Pads not wetting 

properly

  •  Dist. tube holes 

clogged

  •  Pump not working 

properly

 • Insuffi cient water fl ow 

over pads

1. Check power

 • Replace fuse
 • Reset breaker
2. Adjust belt tension
3. Determine cause of 

overheating

  •  Adjust belt tension
  •  Grease blower bear-

ings

  •  Oil motor bearings
  •  Adjust pulley to cor-

rect diameter

4. Replace motor

1. Open windows or 

doors to increase air 
fl ow

2. Adjust belt tension or 

replace if needed

3. Clean pads
4. Clean distribution 

system

1. Drain pan and clean 

pads

2. Check water distribu-

tion system

 • Clean

  •  Replace or clean 

pump (Unplug)

  •  Clean water distribu-

tion system

1. Check voltage
2. Adjust belt tension
3. Grease or replace 

bearings (Disconnect 
unit)

4. Grease bearings
5. Adjust pulley so full 

load ampere rating of 
motor is not exceeded

6. Replace motor

1. Grease bearings
2. Inspect and realign 

(Disconnect unit)

3. Tighten loose parts

1. Open windows or 

doors to increase air 
fl ow

2. Check water distribu-

tion system

 • Clean pads
 • Clean

  •  Replace or clean 

pump (Unplug)

1. Open doors or win-

dows

Motor 
cycles on 
and off

Noisy

Inadequate 
cooling

Excessive 
humidity in 
house

1. Low voltage
2. Excessive belt tension
3. Blower shaft tight or 

locked

4. Bearings dry
5. Motor pulley diameter 

too large causing motor 
overload

6. Faulty motor

1. Bearings dry
2. Wheel rubbing blower 

housing

3. Loose parts

1. Inadequate exhaust in 

house

2. Pads not wet

 • Pads plugged
  •  Dist. tube holes 

clogged

  •  Pump not working 

properly

1. Inadequate exhaust