Assa 32 User Manual
Rev. A.5, 8/03
Page- 2
FIG. 1: STEPS IN MOUNTING THE STRIKE
Step four is to insert roll pins furnished with the strike. The pins are hammered into the strike
but be careful not to hit them too hard as it is possible to raise dents on the strike surface by
over driving the pins which degrades strike flatness and therefore holding force. In step five, the
strike is secured by the central strike mounting screw. In step six two flexible washers are then
placed between the strike and the door with the strike mounting screw passing through the
washers to provide flexibility. A third rubber washer is furnished. This is not normally used but
may be employed in case the spacing of the magnet and strike is a little off. Adding the third
washer will move the strike closer to the magnet. Do not place the washers around the roll
pins. The roll pins should "float" in their holes and not bind. Their only purpose is to prevent
the strike from rotating or spinning.
but be careful not to hit them too hard as it is possible to raise dents on the strike surface by
over driving the pins which degrades strike flatness and therefore holding force. In step five, the
strike is secured by the central strike mounting screw. In step six two flexible washers are then
placed between the strike and the door with the strike mounting screw passing through the
washers to provide flexibility. A third rubber washer is furnished. This is not normally used but
may be employed in case the spacing of the magnet and strike is a little off. Adding the third
washer will move the strike closer to the magnet. Do not place the washers around the roll
pins. The roll pins should "float" in their holes and not bind. Their only purpose is to prevent
the strike from rotating or spinning.
In step seven, the strike is secured to the door via the supplied sex bolt. Note that we supply a
massive 1 1/4” diameter sex bolt as it is the only point of attack from the outside of the door. It
can be difficult to align the strike mounting screw with the sex bolt, so the following technique is
recommended: Start the sex bolt in its 1/2" (12.7 mm) hole but thread the strike mounting screw
into it (with strike plate and washers) before hammering the sex bolt down. Next, hammer the
sex bolt down and then screw the strike mounting screw in the rest of the way. This makes
alignment much easier.
massive 1 1/4” diameter sex bolt as it is the only point of attack from the outside of the door. It
can be difficult to align the strike mounting screw with the sex bolt, so the following technique is
recommended: Start the sex bolt in its 1/2" (12.7 mm) hole but thread the strike mounting screw
into it (with strike plate and washers) before hammering the sex bolt down. Next, hammer the
sex bolt down and then screw the strike mounting screw in the rest of the way. This makes
alignment much easier.
Step eight is to verify proper mounting. When the strike is mounted, make sure it flexes
freely around the washer stack. This flexing allows the Magnalock to pull the strike into
perfect alignment for maximum holding force. It is never possible for a door and frame to line
up well enough for the Magnalock to function unless the strike is allowed to flex.
freely around the washer stack. This flexing allows the Magnalock to pull the strike into
perfect alignment for maximum holding force. It is never possible for a door and frame to line
up well enough for the Magnalock to function unless the strike is allowed to flex.
STEP 1: LOCATE STRIKE POSITION ON DOOR
STEP 2: DRILL 3 HOLES IN DOOR
FOLLOWING THE TEMPLATE
FOLLOWING THE TEMPLATE
STEP 3: INSERT
PLASTIC BUSHINGS
PLASTIC BUSHINGS
STEP 4: LIGHTLY HAMMER
IN ROLL PINS,
IN ROLL PINS,
STEP 5: INSERT STRIKE
MOUNTING SCREW THROUGH
WHITE PLASTIC BUSHING
MOUNTING SCREW THROUGH
WHITE PLASTIC BUSHING
STEP 6: INSTALL
2 OR 3 RUBBER
WASHERS
ON STRIKE
MOUNTING
SCREW
2 OR 3 RUBBER
WASHERS
ON STRIKE
MOUNTING
SCREW
STEP 7: SECURE STRIKE TO DOOR USING SEX BOLT (SEE FIGURE 5)
STEP 8: VERIFY MOUNTING
STEP 8: VERIFY MOUNTING