Shark KD450WM User Manual
8
TOLL FREE: 1-800-798-7398
6
Use the Sonic Duo™ to spread the polish
evenly over the floor. Do not go over an applied
area too frequently. Always leave an area
looking wet. If a section begins to look dry while
polishing, add more Wood & Hard Floor Polish to
the area. Repeat until the whole area has been
polished.
area too frequently. Always leave an area
looking wet. If a section begins to look dry while
polishing, add more Wood & Hard Floor Polish to
the area. Repeat until the whole area has been
polished.
7
When going from section to section, do not lift
the Sonic Duo™ to move it, always slide it to
the next section. No rinsing is required.
the next section. No rinsing is required.
8
Allow the Wood & Hard Floor Polish to dry for at
least 1 hour in light traffic areas and a complete
24 hours for the polish to cure before returning
to heavy traffic areas.
24 hours for the polish to cure before returning
to heavy traffic areas.
9
When finished, turn the unit off and slide and lift
the Sonic Duo™ to remove it from the area
that was just polished. Lay the Sonic Duo™
on its side and remove the Hard Floor Polishing
Pad by hand. (Fig. 25)
that was just polished. Lay the Sonic Duo™
on its side and remove the Hard Floor Polishing
Pad by hand. (Fig. 25)
NOTE: Depending on the amount of traffic your
floors sustain, Shark
floors sustain, Shark
®
recommends polishing
every 2 months. Touch up high traffic areas as
needed in-between full floor polishes.
needed in-between full floor polishes.
Polishing Your Hard Floors:
NOTE: Wood & Hard Floor Polishing Pad
and the Wood & Hard Floor Polish are not
included.
and the Wood & Hard Floor Polish are not
included.
1
Vacuum the floor to remove all loose dirt, dust
and grit from the floor surface. For best results,
we recommend that you clean the floor using
the Shark
we recommend that you clean the floor using
the Shark
®
Wood & Hard Floor Cleaner first and
allow time to dry before polishing.
2
Attach the Hard Floor Polishing Pad to the
bottom of the Sonic Duo™. This pad has a
“Orange” trim and the “Orange” tag says “Hard
Floor Polishing Pad”. (Fig. 22)
“Orange” trim and the “Orange” tag says “Hard
Floor Polishing Pad”. (Fig. 22)
3
Lightly step on the back of the scrubbing head to
release the handle.
WARNING: Never stand on the Sonic Duo
WARNING: Never stand on the Sonic Duo
™
.
4
Carefully, squirt a liberal amount of the Floor
Polish onto an area of the floor to be polished
and place the polishing pad over it before you
start the unit. Make sure that the polishing pad
is saturated and then squirt the polish in 5’x5’
sections. (Fig. 23)
and place the polishing pad over it before you
start the unit. Make sure that the polishing pad
is saturated and then squirt the polish in 5’x5’
sections. (Fig. 23)
5
Turn the On/Off button to “On (I Low)” setting.
Always squirt the floor polish from a height of
6 inches above the floor to avoid splashing the
polish over the floor. One bottle is enough to
cover 425 square feet. (Fig. 24)
6 inches above the floor to avoid splashing the
polish over the floor. One bottle is enough to
cover 425 square feet. (Fig. 24)
IMPORTANT: NEVER add the Sonic
Activated Wood & Hard Floor Polish to
the Reusable Bottle or run it through the Sonic
Duo
Activated Wood & Hard Floor Polish to
the Reusable Bottle or run it through the Sonic
Duo
™
unit.
Using Your Sonic Duo
™
Carpet, Wood & Hard Floor Cleaner - cont.
fig. 22
fig. 23
fig. 24
fig. 25
KD450WM_26_IB_E_130128_4.indd 8
13-01-28 3:50 PM