Wayne-Dalton 6100 User Manual
4
Please Do Not Return This Product To The Store. Contact your local Wayne-Dalton dealer. To find your local Wayne-Dalton dealer, refer to your
local yellow pages/business listings or go to the
Find a Dealer section online at www.wayne-dalton.com
Tools Needed:
Door Section identification
hinges are always pre-attached at the top of each
section (except top section) and the hinges are
stamped for identification (except double wide end
hinges), #1, #2, #3, and #4. See view below. The
stamp identifies the stacking sequence of the section.
The sequence is always determined by #1 being the
bottom section to #4 being the highest intermediate
section. See views to the right. If the stamp on the
end hinge is illegible, or double wide end hinges are
installed, refer to the section side view illustration to
the right.
section (except top section) and the hinges are
stamped for identification (except double wide end
hinges), #1, #2, #3, and #4. See view below. The
stamp identifies the stacking sequence of the section.
The sequence is always determined by #1 being the
bottom section to #4 being the highest intermediate
section. See views to the right. If the stamp on the
end hinge is illegible, or double wide end hinges are
installed, refer to the section side view illustration to
the right.
NoTe: The section side view illustration shows the
end hinge profile of all the sections, and can also be
used in conjunction with identifying each sections.
end hinge profile of all the sections, and can also be
used in conjunction with identifying each sections.
The
boTTom SecTioN can be identified by #1 end
hinges, the factory attached astragal, and by the
bottom bracket warning labels on each end stile. This
section is always the 1st section from the bottom of
the door.
bottom bracket warning labels on each end stile. This
section is always the 1st section from the bottom of
the door.
The
lock SecTioN can be identified by #2 end
hinges. This section is always the 2nd section from
the bottom of the door.
the bottom of the door.
The
iNTeRmeDiaTe i SecTioN can be identified by
#3 end hinges. Sections will have a warning label
attached to either the left or the right end stile of the
section. This section is always the 3rd section from
the bottom of the door.
attached to either the left or the right end stile of the
section. This section is always the 3rd section from
the bottom of the door.
The
iNTeRmeDiaTe ii SecTioN can be identified by
#4 end hinges. This section if always the 4th section
from the bottom of the door.
from the bottom of the door.
The
ToP SecTioN can be identified with no pre-
installed end or center hinges on the section and the
warning label attached in the upper middle of the
section.
warning label attached in the upper middle of the
section.
#1 End
hinge
hinge
#2 End
hinge
hinge
#3 End
hinge
hinge
#4 End
hinge
hinge
Astragal
bottom
bracket
bracket
bot.
Lock
1 3/8”
1 5/8”
Int.
1 1/8”
7/8”
SECTION SIDE vIEw
TyPical hiNge STamPiNg locaTioN
Int.#2
Recommended tools
from
page 5
Top section
Warning label
#1
#2
#3
#4
Intermediate I section
Lock section
bottom section
Astragal
Intermediate II section
Warning label
bottom bracket warning labels
hinge
stamping
location
stamping
location
STack heighTS
Door
height
bottom
Lock
(second)
Intermediate
(third)
Intermediate
II (fourth)
Top
9’0”
23.8”
20.8”
20.8”
20.8”
20.8”