Chamberlain 3595S User Manual
16
FLOOR MOUNT (RIGHT SIDE)
WALL MOUNT (RIGHT SIDE)
DOOR TRACK MOUNT (RIGHT SIDE)
Indicator
light
light
Lens
Lip
Sensor
Bracket
Bracket
Door
Track
Track
Sensor
Bracket
Bracket
Extension
Bracket
Bracket
Lens
Indicator
light
light
Lag Screw
1/4x1-1/2"
1/4x1-1/2"
Inside
Garage
Wa
ll
Indicator
light
light
Sensor
Bracket
Bracket
Lens
Extension
Bracket
Bracket
Inside
Ga
Ga
rage
Wall
Lock Nut
1/4"-20
1/4"-20
Lock Nut
1/4"-20
1/4"-20
Hex Bolt
1/4"-20x5/8"
1/4"-20x5/8"
Hex Bolt
1/4"-20x5/8"
1/4"-20x5/8"
Lag Screw
1/4x1-1/2"
1/4x1-1/2"
Figure 3
Figure 1
Figure 2
INSTALLING THE BRACKETS
Be sure power to the opener is disconnected. Install
and align the brackets so the sensors will face each other
across the garage door, with the beam no higher than
6" (15 cm) above the floor. They may be installed in one of
three ways, as follows:
and align the brackets so the sensors will face each other
across the garage door, with the beam no higher than
6" (15 cm) above the floor. They may be installed in one of
three ways, as follows:
Garage door track installation (preferred):
•
Slip the curved arms over the rounded edge of each
door track, with the curved arms facing the door. Snap
into place against the side of the track. It should lie
flush, with the lip hugging the back edge of the track, as
shown in Figure 1.
door track, with the curved arms facing the door. Snap
into place against the side of the track. It should lie
flush, with the lip hugging the back edge of the track, as
shown in Figure 1.
If your door track will not support the bracket securely, wall
installation is recommended.
installation is recommended.
Wall installation:
•
Place the bracket against the wall with curved arms
facing the door. Be sure there is enough clearance for
the sensor beam to be unobstructed.
facing the door. Be sure there is enough clearance for
the sensor beam to be unobstructed.
•
If additional depth is needed, an extension bracket or
wood blocks can be used.
wood blocks can be used.
•
Use bracket mounting holes as a template to locate and
drill (2) 3/16" diameter pilot holes on the wall at each
side of the door, no higher than 6" (15 cm) above the
floor.
drill (2) 3/16" diameter pilot holes on the wall at each
side of the door, no higher than 6" (15 cm) above the
floor.
•
Attach brackets to wall with lag screws.
•
If using extension brackets or wood blocks, adjust right
and left assemblies to the same distance out from the
mounting surface. Make sure all door hardware
obstructions are cleared.
and left assemblies to the same distance out from the
mounting surface. Make sure all door hardware
obstructions are cleared.
Floor installation:
•
Use wood blocks or extension brackets to elevate
sensor brackets so the lenses will be no higher than
6" (15 cm) above the floor.
sensor brackets so the lenses will be no higher than
6" (15 cm) above the floor.
•
Carefully measure and place right and left assemblies at
the same distance out from the wall. Be sure all door
hardware obstructions are cleared.
the same distance out from the wall. Be sure all door
hardware obstructions are cleared.
•
Fasten to the floor with concrete anchors as shown.
Lag Screw
1/4x1-1/2" (4)
1/4x1-1/2" (4)
Lock Nut
1/4"-20 (2)
1/4"-20 (2)
Hex Bolt
1/4"-20x5/8" (2)
1/4"-20x5/8" (2)
Wing Nut
1/4"-20
1/4"-20
Staples
Carriage Bolt
1/4"-20x1/2"
HARDWARE SHOWN ACTUAL SIZE