Chamberlain 1000SD User Manual
Children operating or playing with a garage door opener
can injure themselves or others. The garage door could
close and cause serious injury or death. Do not allow
children to operate the door control(s) or remote control
transmitter(s).
can injure themselves or others. The garage door could
close and cause serious injury or death. Do not allow
children to operate the door control(s) or remote control
transmitter(s).
A moving garage door could injure or kill someone under
it. Activate the opener only when you can see the door
clearly, it is free of obstructions, and is properly
adjusted.
it. Activate the opener only when you can see the door
clearly, it is free of obstructions, and is properly
adjusted.
Your garage door opener receiver and remote control
transmitter have been set at the factory to a matching
code. The door will activate when the remote control
push button is pressed.
transmitter have been set at the factory to a matching
code. The door will activate when the remote control
push button is pressed.
Your "Smart" garage door opener will operate with:
• up to four "Smart" remote control transmitters (with
green indicator lights),
• a Keyless Entry System, and
• code switch remote controls with red indicator lights.
Below are instructions for programming your opener to
match any additional remotes you may purchase. See
available accessories on page 34.
match any additional remotes you may purchase. See
available accessories on page 34.
To add a single function remote control:
1. Press and hold the remote push button, see Figure 1.
2. Then press and release the "Smart" (learn) button on
the right side panel of the opener, Figure 2. The opener
lights will flash once.
lights will flash once.
3. Release the remote push button.
Now the opener will operate when the remote control
push button is pressed.
push button is pressed.
If you release the remote control push button before
the opener lights flash, the opener will not accept the
code.
the opener lights flash, the opener will not accept the
code.
To change the selected push button on the same
remote:
remote:
If you decide to use a different remote control button than
originally programmed into the opener, you need to erase
all the learned codes and reprogram each remote used to
operate the garage door opener.
originally programmed into the opener, you need to erase
all the learned codes and reprogram each remote used to
operate the garage door opener.
To erase all remote control codes:
• Press and hold the "Smart" button on the opener panel
until the indicator light turns off (about 6 seconds). All
the codes the opener has learned will be erased.
the codes the opener has learned will be erased.
• To reprogram, repeat Steps 1 - 3 for each remote
control in use.
Code programming instructions are also located on
the opener panel.
the opener panel.
29
"Smart"
Single Function Remote Control
Push Button
Green Battery
Indicator Light
Indicator Light
Figure 1
WARNING
CAUTION
WARNING
Receiver & Remote Control Programming
NOTICE: To comply with FCC rules, adjustment or modification of this
receiver and/or transmitter are prohibited, except for changing the code
setting or replacing the transmitter battery. THERE ARE NO OTHER
USER SERVICEABLE PARTS.
receiver and/or transmitter are prohibited, except for changing the code
setting or replacing the transmitter battery. THERE ARE NO OTHER
USER SERVICEABLE PARTS.
Garage Door Opener
(With "Smart" Button)
"Smart" (learn)
Button
Indicator
Light
+
+
3
2
1
Kg
Kg
1
3
8
7
5
1
3
8
7
5
Figure 2
To Add the Keyless Entry
We recommend that you program your code before you
install the Keyless Entry. You will not need assistance,
and you can test the reception at the mounting location
before installation.
install the Keyless Entry. You will not need assistance,
and you can test the reception at the mounting location
before installation.
1. Choose a 4-digit code using numbers from 0 to 9. You
can use a number more than once (for example, 4, 0,
4, 1). Press the selected code digits on the keypad.
4, 1). Press the selected code digits on the keypad.
2. Press and hold the Enter button while you press the
“SRT” (learn) button on the opener panel. The
indicator light will blink and the door will begin to
move.
indicator light will blink and the door will begin to
move.
3. Release the Enter button. Now the opener has learned
the selected keypad code.
To ensure that your portable remote control codes were
not disturbed while you were programming the Keyless
Entry, test your remotes and reprogram them if necessary.
not disturbed while you were programming the Keyless
Entry, test your remotes and reprogram them if necessary.
To change the code at any time, repeat steps 1-3.