Regency L676E-LP User Manual
Regency
®
L676E Direct Vent Gas Fireplace
33
OPERA
TION
OPERATING INSTRUCTIONS
OPERATING
INSTRUCTIONS
1) Read and understand these instructions
before operating this appliance.
2) Check to see that all wiring is correct and
enclosed to prevent possible shock.
3) Check to ensure there are no gas leaks.
4) Make sure the glass in the door frame is
properly positioned. Never operate the
appliance with the glass removed.
appliance with the glass removed.
During the fi rst few fi res, a white fi lm
may develop on the glass front as part of
the curing process. The glass should be
cleaned after the unit has cooled down
or the fi lm will bake on and become very
diffi cult to remove. Use a non-abrasive
cleaner and DO NOT ATTEMPT TO CLEAN
THE GLASS WHILE IT IS HOT.
may develop on the glass front as part of
the curing process. The glass should be
cleaned after the unit has cooled down
or the fi lm will bake on and become very
diffi cult to remove. Use a non-abrasive
cleaner and DO NOT ATTEMPT TO CLEAN
THE GLASS WHILE IT IS HOT.
The FIRST FIRE in your heater is part of the paint
curing process. To ensure the paint is properly
cured, it is recommended you burn your fi replace
for at least four (4) hours the fi rst time.
curing process. To ensure the paint is properly
cured, it is recommended you burn your fi replace
for at least four (4) hours the fi rst time.
When fi rst operated, the unit will release an
odour caused by the curing of the paint and the
burning off of any oils remaining from manufac-
turing. Smoke detectors in the house may go off
at this time. Open a few windows to ventilate
the room for a couple of hours. The glass may
require cleaning.
odour caused by the curing of the paint and the
burning off of any oils remaining from manufac-
turing. Smoke detectors in the house may go off
at this time. Open a few windows to ventilate
the room for a couple of hours. The glass may
require cleaning.
NOTE: The main burner will always start on
"HIGH" and resume it's last setting after
20 seconds of operation.
20 seconds of operation.
NOTE: When the glass is cold and the appliance
is lit, it may cause condensation and fog
the glass. This condensation is normal
and will disappear in a few minutes as
the glass heats up.
the glass. This condensation is normal
and will disappear in a few minutes as
the glass heats up.
DO NOT ATTEMPT TO CLEAN THE
GLASS WHILE IT IS STILL HOT!
GLASS WHILE IT IS STILL HOT!
FIRST FIRE
DO NOT BURN THE APPLIANCE
WITHOUT THE GLASS FRONT IN
PLACE.
WITHOUT THE GLASS FRONT IN
PLACE.
MATCHING REMOTE
HANDSET & CONTROL
BOX ID CODE
The Remote Control Handset has a set of unique
ID codes that is pre-programmed into its memory.
This set of ID codes helps to differentiate one
Remote Control Handset from another so that
only the control box with a matching ID code
will respond to the appropriate Remote Control
Handset.
ID codes that is pre-programmed into its memory.
This set of ID codes helps to differentiate one
Remote Control Handset from another so that
only the control box with a matching ID code
will respond to the appropriate Remote Control
Handset.
To ensure the remote control is matched to
the receiver correctly, please follow the steps
below:
the receiver correctly, please follow the steps
below:
1. Install the 2 x AAA alkaline batteries into the
Remote Control.
2. Unplug and re-plug the power cord. The
power cord is located on the left hand side
of the appliance and will be plugged into the
receptacle.
of the appliance and will be plugged into the
receptacle.
3. Press and hold the PROG and FAN buttons
simultaneously for up to 20 seconds. During
this time, the remote will display LC while it
is transmitting codes to the receiver.
this time, the remote will display LC while it
is transmitting codes to the receiver.
4. Once it is successfully transmitted, wait for
20 seconds and press the ON/OFF button
on the remote control once and the burners
will come on.
on the remote control once and the burners
will come on.
If is does not work the fi rst time, repeat steps
2 and 3.
2 and 3.
5. The remote control is now programmed to
the receiver and the appliance can now be
operated with it.
operated with it.
The control box will only learn the Remote ID
codes during the fi rst 30 seconds after power is
applied and will ignore this special command from
the Remote after the fi rst 30 seconds.
codes during the fi rst 30 seconds after power is
applied and will ignore this special command from
the Remote after the fi rst 30 seconds.
NOTE: This must only be performed by a quali-
fi ed installer.
fi ed installer.
The gas control knob is located on the
right hand side of the fi rebox behind the
right side exterior brick panel.
right hand side of the fi rebox behind the
right side exterior brick panel.
GAS CONTROL VALVE
Right Side Exterior Brick Panel
3) Lift the heat shield up and pull out slightly to
clear the head screws and then hang it on
the top bracket (located directly above the
heat shield, close to the top of the fi rebox).
the top bracket (located directly above the
heat shield, close to the top of the fi rebox).
2) Loosen the 2 screws that hold the right side
heat shield in place.
Heat
Shield
Shield
1) Remove the right side exterior brick panel.
5) Verify that the venting and cap are
unobstructed.
6) Ensure that the brick panels are installed.
7) Verify log placement. If the pilot cannot be
seen when lighting the unit, the logs have
been incorrectly positioned.
been incorrectly positioned.
8) The unit should never be turned off, and on
again without a minimum of a 60 second
wait.
wait.