Regency L676-LP1 User Manual

Regency

L676-1 Direct Vent Gas Fireplace

INST

ALLA

TION

INSTALLATION

L676-NG1 SYSTEM DATA

Canada

USA

Altitude

0 - 2000 ft
(0 - 610m)

Min. Supply
Pressure

5" WC (1.25
kpa)

5" WC
(1.25 kpa)

Low Setting Man.
Pressure

1.6" WC
(0.39 kpa)

Max. Manifold
Pressure

3.5" WC
(0.87 kpa)

Orifi ce Size

#33 DMS

Minimum Input

22,000 Btu/h
(6.45 kW)

22,000
Btu/h
(6.45 kW)

Maximum Input

33,000 Btu/h
(9.67 kW)

33,000
Btu/h
(9.67 kW)

Altitude

2000-4500
ft.
(610-1371m)

2000-4500
ft.
(610-
1371m)

Orifi ce Size

#33 DMS

# 34 DMS

Minimum Input

22,000 Btu/h
(6.45 kW)

21,500
Btu/h
(6.30 kW)

Maximum Input

33,000 Btu/h
(9.67 kW)

32,000
Btu/h
(9.37kW)

L676-LP1 SYSTEM DATA

Altitude

0-4500 ft.
(0 - 1371m)

Min. Supply
Pressure

12" WC
(2.98 kpa)

Low Setting Man.
Pressure

6.4" WC
(1.59 kpa)

Max. Manifold
Pressure

10" WC
(2.49 kpa)

Orifi ce Size

#51 DMS

Minimum Input

25,000 Btu/h
(7.33 kW)

25,000
Btu/h
(7.33 kW)

Maxiumm Input

31,500 Btu/h
(9.23 kW)

31,500
Btu/h
(9.23 kW)

GAS PIPE PRESSURE

TESTING

The appliance must be isolated from the gas
supply piping system by closing its individual
manual shut-off valve during any pressure
testing of the gas supply piping system at
test pressures equal to or less than 1/2 psig.
(3.45 kPa). Disconnect piping from valve at
pressures over 1/2 psig.

The manifold pressure is controlled by a regulator
built into the gas control, and should be checked
at the pressure test point.

Note: To properly check gas pressure, both

inlet and manifold pressures should
be checked using the valve pressure
ports on the valve.

1) Make sure the valve is in the "OFF"

position.

2) Loosen the "IN" and/or "OUT" pressure tap(s),

turning counterclockwise with a

1/8" wide fl at screwdriver.

3) Attach manometer to "IN" and/or "OUT"

pressure tap(s) using a 5/16" ID hose.

4) Light the pilot and turn the valve to "ON"

position.

5) The pressure check should be carried out

with the unit burning and the setting should
be within the limits specifi ed on the safety
label.

6) When

fi nished reading manometer, turn off the

gas valve, disconnect the hose and tighten the
screw (clockwise) with a 1/8" fl at screwdriver.
Note: Screw should be snug, but do not
over tighten.

SIT 829 VALVE DESCRIPTION

1) Gas on/off knob
2) Electronically Operated Hi/Lo
3) Pilot

Adjustment

4)  Thermocouple Connection - option
5)  Outlet Pressure Tap
6) Inlet Pressure Tap
7) Pilot Outlet
8)  Main Gas Outlet
9)  Alternative TC Connection Point

HIGH ELEVATION

This unit is approved in Canada for altitude 0
to 4500 ft. (CAN1 2.17-M91).

GAS LINE

INSTALLATION

Since some municipalities have additional
local codes it is always best to consult with
your local authorities and the CAN/CGA B149
installation code.

PILOT ADJUSTMENT

Periodically check the pilot fl ames. Correct
fl ame pattern has three strong blue fl ames:
1 fl owing around the thermopile, 1 around
the thermocouple and 1 fl owing across the
burner (it does not have to be touching the
burner).

Note: If

you have an incorrect fl ame pattern,

contact your Regency

dealer for

further instructions.

Incorrect fl ame pattern will have small,
probably yellow fl ames, not coming into
proper contact with the rear burner or
thermopile or thermocouple.

IMPORTANT: Always check for gas leaks
with a soap and water solution or gas leak
detector. Do not use open fl ame for leak
testing.

For USA installations follow local codes and/
or the current National Fuel Gas Code, ANSI
Z223.1.

When using copper or fl ex connectors use only
approved fi ttings. Always provide a union so
that gas lines can be easily disconnected for
servicing. Flare nuts for copper lines and fl ex
connectors are usually considered to meet this
requirement.