PGS TC36 AR User Manual
050505-36
36ARB2 23
LIGHTING INSTRUCTIONS - Millivolt Valve
TO TURN OFF GAS TO APPLIANCE
LIGHTING INSTRUCTIONS
1. STOP! Read the safety information above on this label.
2. Set wall thermostat to lowest setting, if applicable.
3. Turn off all electric power to the appliance, if applicable.
4. This appliance is equipped with an ignition device which
2. Set wall thermostat to lowest setting, if applicable.
3. Turn off all electric power to the appliance, if applicable.
4. This appliance is equipped with an ignition device which
automatically lights the pilot. Do not try to light the pilot by
hand.
hand.
5. Partially depress and turn gas control
knob clockwise
past "Pilot" to "Off"
position.
Note: Knob cannot be turned from "Pilot" to
"Off" unless knob is pushed in slightly.
Do not force.
Do not force.
6 Allow
suffi cient length of time (minimum 5 minutes) for any
gas in the combustion chamber to escape. If you still smell
gas, STOP! Follow "B" in the safety information above on
this label. If you don't smell gas, go to the next step.
gas, STOP! Follow "B" in the safety information above on
this label. If you don't smell gas, go to the next step.
7. Turn gas control knob back to "Pilot" position.
WARNING: If you do not follow these instructions
exactly, a fi re or explosion may result causing
property damage, personal injury or loss of life.
property damage, personal injury or loss of life.
A. This appliance is equipped with an ignition device which auto-
matically lights the pilot. Do not try to light the pilot by hand.
B. BEFORE LIGHTING smell all around the appliance area for gas.
Be sure to smell next to the fl oor because some gas is heavier
than air and will settle on the fl oor.
than air and will settle on the fl oor.
WHAT TO DO IF YOU SMELL GAS:
- Do not try to light any appliance.
- Do not touch any electric switch; do not use any phone in your
FOR YOUR SAFETY READ BEFORE LIGHTING
1. Set wall thermostat to lowest setting, if applicable.
2. Turn off all electric power to the appliance if service is to be
2. Turn off all electric power to the appliance if service is to be
performed.
3. Push in gas control knob slightly and turn clockwise
to
"Off". Do not force.
8. Depress gas control knob fully and hold to ignite pilot. Once
the pilot ignites, continue depressing knob for approxi-
mately 5 seconds, or until pilot fl ame indicator is in the RED
zone. If pilot does not stay lit, repeat steps 5 through 8,
allowing a longer period before releasing gas control dial.
mately 5 seconds, or until pilot fl ame indicator is in the RED
zone. If pilot does not stay lit, repeat steps 5 through 8,
allowing a longer period before releasing gas control dial.
- If gas control knob does not pop up when released, stop
and immediately call your service technician or gas sup-
plier.
and immediately call your service technician or gas sup-
plier.
- If the pilot will not stay lit after several tries, turn the gas
control knob to "Off" and call your service technician or gas
supplier.
control knob to "Off" and call your service technician or gas
supplier.
9. Turn gas control knob counter-clockwise
to "On" posi-
tion.
10. Turn HI-LO burner control knob to desired setting.
11. Turn on the burner switch and close control door.
12. Turn on all electric power to the appliance, if applicable.
13. Set thermostat to desired setting, if applicable.
Note:
11. Turn on the burner switch and close control door.
12. Turn on all electric power to the appliance, if applicable.
13. Set thermostat to desired setting, if applicable.
Note:
Suffi cient time must be allowed for air to escape from
lines if the unit is being lit for the fi rst time.
building.
- Immediately call your gas supplier from a neighbour's phone.
Follow the gas supplier's instructions.
Follow the gas supplier's instructions.
- If you cannot reach your gas supplier, call the fi re depart-
ment.
ment.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by hand,
don't try to repair it, call a qualifi ed service technician. Force or
attempted repair may result in a fi re or explosion.
don't try to repair it, call a qualifi ed service technician. Force or
attempted repair may result in a fi re or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualifi ed service technician to inspect the
appliance & to replace any part of the control system & any gas
control which has been under water.
appliance & to replace any part of the control system & any gas
control which has been under water.
FIRST FIRE
When lit for the fi rst time, the fi replace will emit a slight odour
for a couple of hours. This is due to the curing of paints, seal-
ants and lubricants used in the manufacturing process. This
condition is temporary. Open doors and windows to ventilate
area. Smoke and fumes caused by the curing process may
cause discomfort to some individuals.
It is normal for fi replaces fabricated of steel to give off some
expansion and/or contraction noises during the start up or
cool down cycle. Similar noises are found with your furnace
heat exchanger or cook stove oven.
for a couple of hours. This is due to the curing of paints, seal-
ants and lubricants used in the manufacturing process. This
condition is temporary. Open doors and windows to ventilate
area. Smoke and fumes caused by the curing process may
cause discomfort to some individuals.
It is normal for fi replaces fabricated of steel to give off some
expansion and/or contraction noises during the start up or
cool down cycle. Similar noises are found with your furnace
heat exchanger or cook stove oven.
OPERATING
The Town and Country Fireplace comes equipped with either
a manual (millivolt) combination gas valve or an electronic
gas valve. An optional wall switch or thermostat (Canada
only) may be installed to operate the burner automatically on
both types of valve.
a manual (millivolt) combination gas valve or an electronic
gas valve. An optional wall switch or thermostat (Canada
only) may be installed to operate the burner automatically on
both types of valve.
Manual Valve: Once a pilot light has been established,
and the gas valve knob turned to the "ON" position (Manual
Valve) or simply switched on with the "Burner" switch, the unit
may be operated in one of two ways; manually adjusting the
fl ame and/or turning the unit on and off automatically with a
wall thermostat.
and the gas valve knob turned to the "ON" position (Manual
Valve) or simply switched on with the "Burner" switch, the unit
may be operated in one of two ways; manually adjusting the
fl ame and/or turning the unit on and off automatically with a
wall thermostat.