Pelonis HC-0119A User Manual
UNPACKING AND SET-UP INSTRUCTIONS
Unpack your heater and remove
both halves of the base
from the package. Refer to the picture
below:
1. Make sure the heater is unplugged and in the “ OFF” position.
2. TURN THE HEATER UPSIDE DOWN.
2. TURN THE HEATER UPSIDE DOWN.
Unfasten the four screws.
3.
Fix
both halves of the base
as shown.
4.
Insert the four screws and screw them tightly.
5. Turn the heater upright. Your heater is now ready for use.
CAUTION: Risk of fire – Operate heater in upright position only. Any other position could create
a hazardous situation.
a hazardous situation.
OPERATION INSTRUCTIONS
IMPORTANT!
Your heater is equipped with
a polarized alternating current
line plug (a plug having one
blade wider than the other).
This plug will fit into the
power outlet only one way.
This is a safety feature. If
you are unable to insert the
plug fully into the outlet, try
reversing the plug. If the plug
should still fail to fit, contact
your electrician to replace
your outlet. DO NOT defeat
the safety purpose of the
polarized plug.
a polarized alternating current
line plug (a plug having one
blade wider than the other).
This plug will fit into the
power outlet only one way.
This is a safety feature. If
you are unable to insert the
plug fully into the outlet, try
reversing the plug. If the plug
should still fail to fit, contact
your electrician to replace
your outlet. DO NOT defeat
the safety purpose of the
polarized plug.
Control
panel
Front LED
display
display
Carry handle
(behind)
(behind)
Fig.1 Control Panel View
Fig.2 Remote Control Panel View
Place the heater on a firm level surface free from obstructions, and at least
3 ft.
away
from any wall and any other objects such as furniture, curtains, plants or combustible
material.
material.
Plug the heater into a grounded 120V outlet; the buzzer sounds and the “A” Digital
Indicator indicate the room temperature. When the heater is on, every time you press
a key, the buzzer will sound.
Indicator indicate the room temperature. When the heater is on, every time you press
a key, the buzzer will sound.
Press POWER key, the operating mode is switched circularly in sequence of HI -LO -
FAN-OFF,
FAN-OFF,
FAN: The Fan circulates room air only. The heating elements are “ OFF”.
LOW: The Fan and heating elements operate at 900 Watts.
HIGH: The Fan and heating elements operate at 1500 Watts.
LOW: The Fan and heating elements operate at 900 Watts.
HIGH: The Fan and heating elements operate at 1500 Watts.
Temperature setting: When the heater is on (HI or LO), press “ Up” or “ Down” key
and the Digital Indicator will indicate the last set temperature (
and the Digital Indicator will indicate the last set temperature (
75
o
F
is default setting
).
You can now adjust your desired temperature by pressing
the
“ Up” or “ Down” key;
the temperature range is 40-95
o
F
.
If there is no operation in 5 seconds, the setting will
be saved and the Digital Indicator will again display the room temperature.
Once the
temperature is set, the unit will select the operating mode based on the following 2
conditions of A and B:
conditions of A and B:
A. If the setting temperature is higher than the room temperature, the heater
continues heating until the room temperature reaches the setting
temperature. Once the room temperature reaches your setting temperature,
the heater will stop heating. The heater will resume heating when the room
temperature is lower than the set temperature. The heater will cycle on and
off this way to maintain the setting temperature.
temperature. Once the room temperature reaches your setting temperature,
the heater will stop heating. The heater will resume heating when the room
temperature is lower than the set temperature. The heater will cycle on and
off this way to maintain the setting temperature.
Fig.1 Control Panel Functions
A
B
C
Timer
Digital Indicator
Oscillation Switch
A
B
C