Napoleon Fireplaces GD70NT-S User Manual

W415-0434 / C / 03.24.05

Do not use abrasive cleaners to clean plated parts. Buff
lightly with a clean dry cloth. The glass is 3/16" ceramic
glass available from your Napoleon / Wolf Steel Ltd. dealer.
DO NOT SUBSTITUTE MATERIALS. Clean the glass after
the first 10 hours of operation with a recommended gas
fireplace glass cleaner. Thereafter clean as required. DO
NOT CLEAN GLASS WHEN HOT! If the glass is not kept
clean permanent discolouration and / or blemishes may
result.

This fireplace may

be installed in an aftermarket perma-

nently located, manufactured (mobile) home, where not

nently located, manufactured (mobile) home, where not
pr

prohibited b

ohibited b

ohibited by local codes

y local codes

y local codes.....

This fireplace is only for use with the type of gas indicated

This fireplace is only for use with the type of gas indicated
on the r

on the r

on the ra

ating pla

ting pla

ting plate

te. T

. T

. This f

his f

his fir

ire

eplace is not con

place is not con

place is not conv

ver

ertib

tib

tible f

le f

le for use

or use

with other gases, unless a certified kit is used.

with other gases, unless a certified kit is used.
No external electricity (110 volts or 24 volts) is required for

No external electricity (110 volts or 24 volts) is required for

No external electricity (110 volts or 24 volts) is required for
the gas system operation.

the gas system operation.

Expansion / contraction noises during heating up and cool-
ing down cycles are normal and are to be expected. Change
in flame appearance from "HI" to "LO" is more evident in
natural gas than in propane.

FIGURES 2a-c

Use only Wolf Steel, Simpson Dura-Vent,

Selkirk Direct

Temp or American Metal Amerivent

venting components.

Minimum and maximum vent lengths, for both horizontal
and vertical installations, and air terminal locations for ei-
ther system are set out in this manual and must be ad-
hered to. For Simpson Dura-Vent,

Selkirk Direct Temp

and American Metal Amerivent

, follow the installation

procedure provided with the venting components.
For vent systems that provide seals on the inner exhaust
flue, only the outer air intake joints must be sealed using a
red high temperature silicone (RTV). This same sealant
maybe used on both the inner exhaust and outer intake
vent pipe joints of all other approved vent systems except
for the exhaust vent pipe connection to the fireplace flue
collar which must be sealed using the black high tem-
perature sealant Mill Pac. High temperature sealant must
be ordered separately.
When using Napoleon venting components, use only ap-
proved Wolf Steel Ltd. rigid / flexible vent components with
the following termination kits: WALL TERMINAL KIT GD222,
or 1/12 TO 7/12 PITCH ROOF TERMINAL KIT GD110, 8/12
TO 12/12 ROOF TERMINAL KIT GD111, FLAT ROOF TER-
MINAL KIT GD112 or PERISCOPE KIT GD201 (for wall pen-
etration below grade). With flexible venting, in conjunction
with the various terminations, use either the 5 foot vent kit
GD220 or the 10 foot vent kit GD330. These vent kits allow
for either horizontal or vertical venting of the fireplace. FIG-
URES 2, 3, & 5.
The maximum allowable vertical vent length is 40 feet.
The maximum number of allowable 4" vent connections is
three horizontally or vertically (excluding the fireplace and
the air terminal connections) when using aluminum flex-
ible venting.
For optimum flame appearance and fireplace performance,
keep the vent length and number of elbows to a minimum.
The air terminal must remain unobstructed at all times.
Examine the air terminal at least once a year to verify that it
is unobstructed and undamaged.

FIGURE 3

CARE OF GLASS, AND PLATED PARTS

When venting, the horizontal run must be kept to a mini-
mum of 12 inches or a maximum of 20 feet. If a 20 foot
horizontal run is required, the fireplace must have a
minimum vertical rise immediately off the fireplace of
57 inches. FIGURES

FIGURES

FIGURES 2a-c

2a-c

2a-c..... When terminating vertically,

the vertical rise is a minimum 34 inches and a maximum
40 feet above the fireplace. FIGURE 3.

FIGURE 3.

Horizontal runs may have a 0 inch rise per foot in all
cases using SIMPSON DURA-VENT or NAPOLEON
RIGID OR FLEXIBLE venting components when vent-
ing as illustrated in Figures 2a, 2b, and 2c.

VENTING

VENTING LENGTHS & AIR TERMINAL LOCATIONS

For optimum performance, it is recommended that all

For optimum performance, it is recommended that all
horizontal runs have a minimum ¼ inch rise per foot.

horizontal runs have a minimum ¼ inch rise per foot.

horizontal runs have a minimum ¼ inch rise per foot.
Wolf Steel rigid and flexible venting systems must not
be combined.
Wolf Steel, Simpson Dura-Vent,

Selkirk Direct Temp and

American Metal Amerivent

venting systems must not

be combined.
Provide a means for visually checking the vent connec-

Provide a means for visually checking the vent connec-

Provide a means for visually checking the vent connec-
tion to the fireplace after the fireplace is installed.

tion to the fireplace after the fireplace is installed.

tion to the fireplace after the fireplace is installed.
Do not allow the inside liner to bunch up on horizontal or

Do not allow the inside liner to bunch up on horizontal or

Do not allow the inside liner to bunch up on horizontal or
v

ver

ertical r

tical r

tical runs and elbows

uns and elbows

uns and elbows. K

. K

. Kee

eep it pulled tight. A

p it pulled tight. A

p it pulled tight. A 1¼"

1¼"

1¼" air

air

gap between the inner and outer liner all around is re-

gap between the inner and outer liner all around is re-
quired for safe operation.

quired for safe operation.

quired for safe operation.
V

Vent lengths tha

ent lengths tha

ent lengths that pass thr

t pass thr

t pass through unhea

ough unhea

ough unheated spaces (a

ted spaces (a

ted spaces (at-

tics, garages, crawl space) should be wrapped with a

tics, garages, crawl space) should be wrapped with a
protective insulation sleeve to minimize condensation.

protective insulation sleeve to minimize condensation.

protective insulation sleeve to minimize condensation.
Use a firestop when penetrating interior walls, floor or

Use a firestop when penetrating interior walls, floor or

Use a firestop when penetrating interior walls, floor or
ceiling.

ceiling.

ceiling.
In order to avoid the possibility of exposed insulation or

In order to avoid the possibility of exposed insulation or

In order to avoid the possibility of exposed insulation or
v

apour bar

pour bar

pour barrier coming in contact with the f

rier coming in contact with the f

rier coming in contact with the fir

ire

eplace body

place body

place body,,,,,

it is recommended that the walls of the fireplace enclo-

it is recommended that the walls of the fireplace enclo-
sur

sur

sure be 'f

e be 'f

e be 'finished', (i.e

inished', (i.e

inished', (i.e. dryw

. dryw

. drywall/sheetr

all/sheetr

all/sheetroc

ock) as w

k) as w

k) as would any

ould any

other outside w

other outside wall of

all of

all of the home

the home

the home. T

. T

. This will ensur

his will ensur

his will ensure tha

e tha

e thattttt

clearance to combustibles is maintained within the cav-

clearance to combustibles is maintained within the cav-
ity

ity

ity.....
For safe and proper operation of the fireplace follow

For safe and proper operation of the fireplace follow

For safe and proper operation of the fireplace follow
the v

the v

the venting instr

enting instr

enting instruction e

uction e

uction exactly

xactly

xactly.....

Deviation from the minimum vertical vent length can cre-

Deviation from the minimum vertical vent length can cre-
ate difficulty in burner start-up and/or carboning.

ate difficulty in burner start-up and/or carboning.