Procom ML200HBA User Manual

Attaching  Mounting  Bracket  to
Wall
Note:  Wall  anchors,  mounting
screws,  and  spacers  are  in
hardware  package.  The    hardware
package  is  provided    with  heater.
Attaching  to  Wall Stud  Method
For  attaching  mounting  bracket to
wall  studs
1.     Drill  holes at marked locations
        using  9/64

"

  drill  bit.

2.     Place  mounting  bracket  onto
        wall. Line up last hole on each
        end of bracket with holes drilled
         in wall.
3.     Insert mounting screws through
         bracket and into wall studs.
4.     Tighten screws until mounting
        bracket is firmly fastened to
        wall studs.
Attaching  to  Wall  Anchor
Method
For  attaching  mounting  bracket to
hollow  walls  (wall  areas between
studs) or solid  walls (concrete or
masonry)
1.   Drill holes at marked  locations
       using  5/16

"

 drill bit.  For  solid

      walls  (concrete  or masonry),
      drill  at  least 1

"

  deep.

2.   Fold  wall  anchor as  shown in
      Figure 9  below.

3.    Insert  wall  anchor  (wings
       first) into hole. Tap  anchor
       flush  to  wall.
4.    For  thin  walls (1/2

"

  or  less),

       insert  red  key  into  wall
       anchor.  Push  red  key  to
       

"

pop

"

  open  anchor  wings

       (see  Figure 10).

           IMPORTANT:  Do  not
hammer    key!   For thick walls
(over  1/2

"

  thick)  or  solid  walls,

do  not  pop  open  wings.

5.   Place  mounting  bracket  onto
       wall.  Line  up  last  hole  on
       each end  of  bracket  with wall
       anchors.
6.   Insert  mounting  screws through
      bracket  and  into  wall anchors.
7.   Tighten  screws  until  mounting
      bracket  is  firmly  fastened  to
      wall.

1.   Locate  two  horizontal   slots  on
    back  panel  of  heater (see
      Figure 11).
2.  Place  heater  onto  mounting
     bracket.  Slide  horizontal  slots
    onto   stand-out    tabs    on
      mounting  bracket.

Installing  Bottom  Mounting
Screws
1.   Locate  two  bottom  mounting
      holes. These  holes  are  near
       bottom    on      back     panel   of
        heater(see Figure 12).

2.   Mark       screw     locations     on
      wall.
3.  Remove  heater   from   mounting
       bracket.
4.  If  installing  bottom  mounting
       screws into  hollow   or   solid   wall,

install  wall  anchors.  Follow  steps
1  through   4    under    Attaching

       To  Wall   Anchor   Method.  If
    installing    bottom   mounting
      screw      into       wall     stud,    drill
     holes   at    marked    locations
      using   9/64

"

  drill  bit.

5.   Replace  heater  onto  mounting
      bracket.
6.   Place        spacers       between’
       bottom     mounting     holes    and
       wall  anchor  or  drilled  holes.
7.    Hold  spacer  in  place   with   one
      hand. With  other  hand,  insert
       mounting         screw         through
      bottom    mounting   hole   and
     spacer.  Place tip  of  screw  in
      opening   of     wall     anchor    or
      drilled  holes.
8.   Tighten  both  screws  until heater
      is  firmly   secured   to    wall.  Do
      not over  tighten.

 

Note:  Do  not  replace  lower front

      panel  at  this  time. Replace  lower
     front  panel   after   making  gas
     connections  and  checking  for
      leaks(see  page  10) .