Desa CGEFP33NRB User Manual
111245-01A
For more information, visit www.desatech.com
For more information, visit www.desatech.com
26
CLEANING PILOT AIR INLET HOLE
Clean the pilot assembly also. A yellow tip on the pilot flame
indicates dust and dirt in the pilot assembly. There is a small pilot
air inlet hole about two inches from where the pilot flame comes out
of the pilot assembly (see Figure 54). With the unit off, lightly blow
air through the air inlet hole. You may blow through a drinking straw
if compressed air is not available. You may also clean the pilot air
inlet hole by pushing a common pipe cleaner completely through the
air inlet hole once.
indicates dust and dirt in the pilot assembly. There is a small pilot
air inlet hole about two inches from where the pilot flame comes out
of the pilot assembly (see Figure 54). With the unit off, lightly blow
air through the air inlet hole. You may blow through a drinking straw
if compressed air is not available. You may also clean the pilot air
inlet hole by pushing a common pipe cleaner completely through the
air inlet hole once.
CLEANING AND MAINTENANCE
Cleaning Burner Injector Holder
Cleaning Pilot Air Inlet Hole
Logs
Cleaning Pilot Air Inlet Hole
Logs
LOGS
• If you remove logs for cleaning, refer to Installing Logs, pages
21 and 22, to properly replace logs.
• Replace log(s) if broken or chipped (dime-sized or larger).
Figure 54 - Pilot Inlet Air Hole (Natural Gas Model Shown)
Burner
Tube
Tube
Pilot
Assembly
Assembly
Pilot Air
Inlet
Hole
Inlet
Hole
Ports/Slots
CLEANING AND
MAINTENANCE
MAINTENANCE
WARNING: Turn off fireplace and let cool before
cleaning.
CAUTION: You must keep control areas, burners,
and circulating air passageways of fireplace clean.
Inspect these areas of fireplace before each use.
Have fireplace inspected yearly by a qualified service
person. Fireplace may need more frequent cleaning
due to excessive lint from carpeting, bedding mate-
rial, pet hair, etc.
Inspect these areas of fireplace before each use.
Have fireplace inspected yearly by a qualified service
person. Fireplace may need more frequent cleaning
due to excessive lint from carpeting, bedding mate-
rial, pet hair, etc.
CLEANING BURNER INJECTOR HOLDER
The primary air inlet holes allow the proper amount of air to mix with
the gas. This provides a clean burning flame. Keep these holes clear
of dust, dirt, lint, and pet hair. Clean these air inlet holes prior to each
heating season. Blocked air holes will create soot. We recommend
that you clean the unit every three months during operation and have
heater inspected yearly by a qualified service person.
the gas. This provides a clean burning flame. Keep these holes clear
of dust, dirt, lint, and pet hair. Clean these air inlet holes prior to each
heating season. Blocked air holes will create soot. We recommend
that you clean the unit every three months during operation and have
heater inspected yearly by a qualified service person.
We also recommend that you keep the burner tube and pilot assembly
clean and free of dust and dirt. To clean these parts we recommend using
compressed air no greater than 30 PSI. Your local computer store,
hardware store, or home center may carry compressed air in a can. You
can use a vacuum cleaner in the blow position. If using compressed air
in a can, please follow the directions on the can. If you don't follow
directions on the can, you could damage the pilot assembly.
clean and free of dust and dirt. To clean these parts we recommend using
compressed air no greater than 30 PSI. Your local computer store,
hardware store, or home center may carry compressed air in a can. You
can use a vacuum cleaner in the blow position. If using compressed air
in a can, please follow the directions on the can. If you don't follow
directions on the can, you could damage the pilot assembly.
1.
Shut off the unit, including the pilot. Allow the unit to cool for
at least thirty minutes.
at least thirty minutes.
2.
Inspect burner, pilot, and primary air inlet holes on injector
holder for dust and dirt (see Figure 53).
holder for dust and dirt (see Figure 53).
3.
Blow air through the ports/slots and holes in the burner.
4.
Check the injector holder located at the end of the burner tube
again. Remove any large particles of dust, dirt, lint, or pet hair
with a soft cloth or vacuum cleaner nozzle.
again. Remove any large particles of dust, dirt, lint, or pet hair
with a soft cloth or vacuum cleaner nozzle.
5.
Blow air into the primary air holes on the injector holder.
6.
In case any large clumps of dust have now been pushed into
the burner repeat steps 3 and 4.
the burner repeat steps 3 and 4.
Figure 53 - Injector Holder On Outlet Burner Tube
Burner
Tube
Tube
Injector Holder