Desa CSDPBN User Manual
111739-01A
For more information, visit www.desatech.com
For more information, visit www.desatech.com
25
25
STOVE AND BURNER
SYSTEM INSTALLATION
SYSTEM INSTALLATION
Continued
3
4
Figure 57 - Installing Log No. 3
Figure 58 - Installing Log No. 4
WARNING: The glass door must be securely in
place before running this burner system. Do not run
this burner system if glass is missing or broken.
this burner system if glass is missing or broken.
NOTICE: Do not put lava rock on burner or under
burner. Placing lava rock on burner could cause
performance problems.
burner. Placing lava rock on burner could cause
performance problems.
5.
Lava rock may be placed along sides and front inside burner
system bottom. This may not be visible when you have re-
placed the front of the stove. It is not necessary to use all of
the lava rock provided.
system bottom. This may not be visible when you have re-
placed the front of the stove. It is not necessary to use all of
the lava rock provided.
Figure 59 - Placing Ember Material on Burner
STOVE AND BURNER SYSTEM INSTALLATION
Installing Logs, Lava Rock and Glowing Embers (Cont.)
OPERATING STOVE AND BURNER SYSTEM
For Your Safety Read Before Lighting
Lighting Instructions
6.
Pull ember material apart into pieces no larger than a dime.
Place these pieces loosely and sparingly directly onto the ex-
posed section of the front burner and along the space between
the burner and grate prongs (see Figure 59). This will create
the glowing ember appearance as the flame touches the ember
material. Do not block air slots by using too much ember ma-
terial in one area. It is not necessary to use all of the ember
material provided.
Place these pieces loosely and sparingly directly onto the ex-
posed section of the front burner and along the space between
the burner and grate prongs (see Figure 59). This will create
the glowing ember appearance as the flame touches the ember
material. Do not block air slots by using too much ember ma-
terial in one area. It is not necessary to use all of the ember
material provided.
7.
Replace the glass door and stove front. See Removing/Re-
placing Glass Door, page 6.
placing Glass Door, page 6.
OPERATING STOVE WITH
BURNER SYSTEM
BURNER SYSTEM
WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing prop-
erty damage, personal injury or loss of life.
erty damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by hand.
When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the floor because some gas
is heavier than air and will settle on the floor.
is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in
• Do not try to light any appliance.
• Do not touch any electric switch; do not use any phone in
your building.
• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by hand,
don't try to repair it, call a qualified service technician. Force
or attempted repair may result in a fire or explosion.
don't try to repair it, call a qualified service technician. Force
or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system
and any gas control which has been under water.
the appliance and to replace any part of the control system
and any gas control which has been under water.
FOR YOUR SAFETY
READ BEFORE LIGHTING
LIGHTING
INSTRUCTIONS
1.
STOP! Read the safety information above.
2.
Turn ON/OFF switch, located on side of rear cover, to “OFF”.
3.
Open lower door panel.
4.
Turn off all electric power to the burner system.
5.
Push in gas control knob slightly and turn clockwise
to “OFF”.
to “OFF”.
6.
Wait five (5) minutes to clear out any gas. Then smell for
gas, including near the floor. If you smell gas, STOP! Fol-
low “B” in the safety information above. If you don't smell
gas, go to the next step.
gas, including near the floor. If you smell gas, STOP! Fol-
low “B” in the safety information above. If you don't smell
gas, go to the next step.
7.
The pilot is located by the main burner and should not re-
quire accessing for lighting.
quire accessing for lighting.
8.
Turn gas control knob counterclockwise
to “PILOT”.