York F3EH090 User Manual
rate request for inspection by the carrier's agent should be
made in writing.
made in writing.
LIMITATIONS
These units must be installed in accordance with all national
and local safety codes. If no local codes apply, installation must
conform with the appropriate national codes. Units are de-
signed to meet National Safety Code Standards. If components
are to be added to a unit to meet local codes, they are to be in-
stalled at the dealer's and/or the customer's expense. See Ta-
ble 2 for application limitations.
and local safety codes. If no local codes apply, installation must
conform with the appropriate national codes. Units are de-
signed to meet National Safety Code Standards. If components
are to be added to a unit to meet local codes, they are to be in-
stalled at the dealer's and/or the customer's expense. See Ta-
ble 2 for application limitations.
LOCATION
These indoor units are not designed for outdoor installation.
They must be located within the building structure, either inside
or outside the conditioned space.
They must be located within the building structure, either inside
or outside the conditioned space.
The units should be located as close to the outdoor units as
practical and positioned to minimize bends in the refrigerant
piping.
practical and positioned to minimize bends in the refrigerant
piping.
Units being installed vertically or horizontally can be set directly
on a floor or platform, or they can be supported by metal or
wooden beams.
on a floor or platform, or they can be supported by metal or
wooden beams.
Units being installed horizontally can be suspended from
above. Four 3/8" weld nuts are provided in the unit frame to ac-
commodate hanger rods. Knockouts must be removed from
the unit panels to expose these weld nuts. Refer to Figure 1 for
their location and the individual load on each hanger rod.
above. Four 3/8" weld nuts are provided in the unit frame to ac-
commodate hanger rods. Knockouts must be removed from
the unit panels to expose these weld nuts. Refer to Figure 1 for
their location and the individual load on each hanger rod.
WARNING: Be careful when attaching the hanger rods. Use a
washer with a back-up nut on each rod and tighten
down against the cabinet so they will not be al-
lowed to turn or slip.
down against the cabinet so they will not be al-
lowed to turn or slip.
RIGGING AND HANDLING
Exercise care when moving the unit. Do not remove any pack-
aging until the unit is near the place of installation.
aging until the unit is near the place of installation.
The packaging consists of a bottom wooden skid that can be
lifted with a fork truck from any direction, a cardboard container
that covers the entire unit, and strapping that secures the card-
board container to the bottom skid.
lifted with a fork truck from any direction, a cardboard container
that covers the entire unit, and strapping that secures the card-
board container to the bottom skid.
These units can be rigged with slings under the bottom skid.
CAUTION: Spreader bars should be used to prevent the
slings from crushing the unit panels and frame.
Before rigging any unit, determine its weight from Table 1. Bef-
ore rigging a unit for horizontal installation, determine its center
of gravity from Figure 1, and make sure that its weight will be
distributed equally.
ore rigging a unit for horizontal installation, determine its center
of gravity from Figure 1, and make sure that its weight will be
distributed equally.
CLEARANCES
All units require certain minimum clearances for proper opera-
tion and service. Refer to Figure 12 for these clearances.
tion and service. Refer to Figure 12 for these clearances.
035-09651-001-A-0304
Unitary Products Group
3
INSTALLATION
DESCRIPTION
UNIT MODEL
F3EH090
F4EH120
Coil
Rows Deep x Rows High
3 x 24
4 x 32
Finned Length - inches
45.5
45.5
Face Area - square feet
7.6
10.1
Tube (Copper) OD - inches
3/8
3/8
Fins (Aluminum) per inch
13
13
Centrifugal Blower (Forward Curve)
Diameter x Width - inches
15 X 15
15 X 15
Blower Motor
1
Nominal Rating - HP
1-1/2
2
Filters (Throwaway)
Quantity Per Unit - 16" x 25" x 1"
4
4
Total Face Area - square feet
11.1
11.1
Refrigerant-22 (Lbs.)
2
Pumpdown Capacity
12.0
22.0
Unit Weight (lbs.)
Shipping
405
440
Operating
365
400
Accessory Operating Weights (Lbs.)
Electric Heaters
10 KW
63
63
16 KW
66
66
26 KW
71
71
36 KW
74
74
Supply Air Plenum
102
102
Base
60
60
Return Air Grille
15
15
1
All of these 1750 RPM motors have a solid base, a 56 frame, a 1.15 service factor, inherent protection & permanently lubricated ball bearings. Refer to page 6 for additional motor & drive data.
2
Refer to Form 035-15410-002 for system charge.
TABLE 1 - PHYSICAL DATA