Blue Sea Systems PN 8244 Leaflet

Input Voltage: 

8244/9353  0-150 Volts AC

 8245/9354 

0-250 

Volts 

AC

Amperage Draw:  1 Milliampere
Display: Analog 

scale

Accuracy: 

3% of scale range

Face Width: 

8244/8245  2 

50.80

 9353/9354 

2-5/8 

66.70

Mounting Hole:  8244/8245  1-1/2  38.10
 9353/9354 

1-7/8 

47.60

 

 

Select a mounting location which is protected from water on the meter front and back and is not  

 

in an area where fl ammable vapors from propane, gasoline or lead acid batteries accumulate.    

 

The meter is not ignition protected and may ignite such vapors. There are two mounting  

 

 

methods for the meters, surface mount or panel mount.

Surface Mount: Drill fi ve clearance holes as shown below. The part number of the meter will 
determine the size and location of the clearance holes. Use the nuts and washers supplied in the 
accessory package to secure the four mounting studs to the mounting surface. This method will 
work on mounting surfaces up to 5/8” thick.

0-150 Volts  PN 8244 / PN 9353

0-250 Volts  PN 8245 / PN 9354

Marine Electrical Products

9332 Rev. 003

It is not possible within the scope of these 
instructions to fully acquaint the installer 
with all the knowledge of electrical systems 
that may be necessary to correctly install 
this product. If the installer is not 
knowledgeable in electrical systems we 
recommend that an electrical professional 
be retained to make the installation.

 

Disconnect all AC power originating on or 
off the vessel. This includes inverters, 
generators, shore power attachments and 
any other device capable of supplying AC 
power to the ship’s circuits. Disconnect the 
main positive DC cable from all batteries to 
eliminate the possibility of a short circuit 
and to disable the inverter while installing 
the meter.

Panel Mount: For thicker mounting surfaces, the meter can be mounted into a 0.125” thick 
panel. Blue Sea Systems offers meter mounting panels for our standard size meters only. Use 
PN 8013 to mount a single meter or PN 8014 to mount two meters.

(

Micro Meters

Standard Meters

Any Blue Sea Systems product with which 
a customer is not satisfi ed may be returned 
for a refund or replacement at any time. 

Input Voltage: 

8244/9353  0-150 Volts AC

 8245/9354 

0-250 

Volts 

AC

Amperage Draw:  1 Milliampere
Display: Analog 

scale

Accuracy: 

3% of scale range

Face Width: 

8244/8245  2 

50.80

 9353/9354 

2-5/8 

66.70

Mounting Hole:  8244/8245  1-1/2  38.10
 9353/9354 

1-7/8 

47.60

 

 

Select a mounting location which is protected from water on the meter front and back and is not  

 

in an area where fl ammable vapors from propane, gasoline or lead acid batteries accumulate.    

 

The meter is not ignition protected and may ignite such vapors. There are two mounting  

 

 

methods for the meters, surface mount or panel mount.

Surface Mount: Drill fi ve clearance holes as shown below. The part number of the meter will 
determine the size and location of the clearance holes. Use the nuts and washers supplied in the 
accessory package to secure the four mounting studs to the mounting surface. This method will 
work on mounting surfaces up to 5/8” thick.

0-150 Volts  PN 8244 / PN 9353

0-250 Volts  PN 8245 / PN 9354

Marine Electrical Products

9332 Rev. 003

It is not possible within the scope of these 
instructions to fully acquaint the installer 
with all the knowledge of electrical systems 
that may be necessary to correctly install 
this product. If the installer is not 
knowledgeable in electrical systems we 
recommend that an electrical professional 
be retained to make the installation.

 

Disconnect all AC power originating on or 
off the vessel. This includes inverters, 
generators, shore power attachments and 
any other device capable of supplying AC 
power to the ship’s circuits. Disconnect the 
main positive DC cable from all batteries to 
eliminate the possibility of a short circuit 
and to disable the inverter while installing 
the meter.

Panel Mount: For thicker mounting surfaces, the meter can be mounted into a 0.125” thick 
panel. Blue Sea Systems offers meter mounting panels for our standard size meters only. Use 
PN 8013 to mount a single meter or PN 8014 to mount two meters.

(

Micro Meters

Standard Meters

Any Blue Sea Systems product with which 
a customer is not satisfi ed may be returned 
for a refund or replacement at any time.