Sony MKE-9040M User Manual
1-8
MVE-9000 IM
1-5. Rack Mounting
The MVE-9000 installs in a 19-inch standard rack.
To mount the MVE-9000 in a rack, use the specified rack
mount kit and follow the procedure described below.
To mount the MVE-9000 in a rack, use the specified rack
mount kit and follow the procedure described below.
Specified rack mount kit : RMM-10
n
If a rack mount kit other than the specified one is used, the
unit may not be correctly install in a 19-inch standard rack.
n
If a rack mount kit other than the specified one is used, the
unit may not be correctly install in a 19-inch standard rack.
Parts of the RMM-10
. Rack tools
. Rack tools
2 pcs
. Right rack mount adaptor
1 pc
. Left rack mount adaptor
1 pc
. Rack tool attaching screws
6 pcs
(B4
x 6 : 7-682-560-09)
. Rack tool attaching screws
6 pcs
(B4
x 10 : 7-682-560-10)
1. Precautions for rack mounting
w
. To prevent the rack from falling or moving, fix the rack
w
. To prevent the rack from falling or moving, fix the rack
on a flat and steady floor using bolts or other fixings.
If the rack falls due to the weight of the equipment, it
may cause death or injury.
If the rack falls due to the weight of the equipment, it
may cause death or injury.
. Be sure to use the specified rack mount kit.
If not, injury may result and the equipment may fall due
to insufficient strength.
to insufficient strength.
. After rack mounting, be sure to tighten the screws on the
rack angle and fix the unit in the rack.
If the screws on the rack angle are not tightened, the unit
may slip from the rack and fall, causing injury.
If the screws on the rack angle are not tightened, the unit
may slip from the rack and fall, causing injury.
c
When mounting the unit in the rack, note the following:
. Be sure to mount in the rack with two persons or more.
. Be careful not to catch your fingers or hands in the rack
When mounting the unit in the rack, note the following:
. Be sure to mount in the rack with two persons or more.
. Be careful not to catch your fingers or hands in the rack
mount rail or others.
. Mount in the rack in a stable position.
n
If several units are mounted in a rack, it is recommended
that a ventilation fan is installed to prevent temperature rise
inside the rack.
If several units are mounted in a rack, it is recommended
that a ventilation fan is installed to prevent temperature rise
inside the rack.
2. Rack mounting procedure
This section describes the rack mounting procedure using
the RMM-10 rack mount kit.
This section describes the rack mounting procedure using
the RMM-10 rack mount kit.
n
Tighten the screws to the following torque.
Tightening torque : 120
Tighten the screws to the following torque.
Tightening torque : 120
x 10
_2
N
.m {12.2 kgf.cm}
1.
Attach the rack tool to the side of the equipment using
the specified six screws.
n
Use B4
the specified six screws.
n
Use B4
x 6 screws.
2.
Loosen the screws on the rear of the right and left
adaptors and adjust the length of the adaptor according
to the depth of the rack.
(The illustration below shows the left adaptor.)
adaptors and adjust the length of the adaptor according
to the depth of the rack.
(The illustration below shows the left adaptor.)
n
Maximum depth of adaptor : 750 mm
Minimum depth of adaptor : 595 mm
Maximum depth of adaptor : 750 mm
Minimum depth of adaptor : 595 mm
B4
x 6
B4
x 6
Rack tool
Rack tool
B4
x 6
B4
x 6
Adaptor
Portion of
the rail
the rail