Sony MKE-9040M User Manual
1-21
MVE-9000 IM
TP701 (G-7), TP801 (G-7), TP901 (E-7), TP1001
(E-7), TP1101 (K-6), TP1201 (K-6), TP1301 (J-6),
TP1401 (H-6), TP1501 (N-6), TP1601 (N-6), TP1701
(M-6), TP1801 (M-6) : ERR terminal
Used for design purpose.
(E-7), TP1101 (K-6), TP1201 (K-6), TP1301 (J-6),
TP1401 (H-6), TP1501 (N-6), TP1601 (N-6), TP1701
(M-6), TP1801 (M-6) : ERR terminal
Used for design purpose.
TP3102 (C-6) : CKX (control timing) signal check
terminal
Use this terminal to check the CKX signal supplied from
mother board.
mother board.
TP3103 (C-6) : FD signal check terminal
Use this terminal to check the FD signal supplied from
mother board.
Use this terminal to check the FD signal supplied from
mother board.
TP3104 (C-6) : HD (horizontal sync) signal check
terminal
Use this terminal to check the HD signal supplied from
mother board.
mother board.
TP3105 (C-5) : VD (vertical sync) signal check
terminal
Use this terminal to check the VD signal supplied from
mother board.
mother board.
TP3401 (A-9), TP3402 (A-9), TP3403 (A-10),
TP3404 (A-9) : DBG3-0 check terminal
Used for design purpose.
TP3404 (A-9) : DBG3-0 check terminal
Used for design purpose.
<LEDs on the CPU-DR module> (C-11)
Refer to <LED on the CPU-DR module> in “1. CA-
54CFA Board”.
Refer to <LED on the CPU-DR module> in “1. CA-
54CFA Board”.
<Switches on the CPU-DR module> (C-11)
Refer to <Switches on the CPU-DR module> in “1. CA-
54CFA Board”.
Refer to <Switches on the CPU-DR module> in “1. CA-
54CFA Board”.
D3401, D3402, D3403, D3404 (A-10) : DBG7-4
status LED
Used for design purpose.
ND3401 (A-10), ND3402 (A-11) : STATUS LED
VIF-28 board CPU status indication.
VIF-28 board CPU status indication.
<Switches>
S3201 (A-8) : CPU CONFIG switch
Used for maintenance purpose.
S3201 (A-8) : CPU CONFIG switch
Used for maintenance purpose.
S3401 (A-10) : SETUP switch
Used for maintenance purpose.
Used for maintenance purpose.
<Connectors>
CN3202 (A-7) : USB terminal
Used for debugging.
CN3202 (A-7) : USB terminal
Used for debugging.
CN3203 (A-8) : TERMINAL pin
This pin is connected to the sub CPU control terminal and
used during maintenance. Conforms to RS-232C.
This pin is connected to the sub CPU control terminal and
used during maintenance. Conforms to RS-232C.
CN4001 (A-9) : ISP common connector
Used only for production in the assembly factory. Used for
program writing into the JTAG device with ISP.
Used only for production in the assembly factory. Used for
program writing into the JTAG device with ISP.
<TEST terminals>
E601 (H-4), E604 (C-9), E605 (N-2), E606 (C-7),
E607 (A-11), E608 (B-5), E609 (L-4), E610 (N-6),
E611 (E-4), E622 (F-7), E623 (A-2), E625 (J-6),
E626 (F-7), E627 (F-10) : GND terminals
Use these terminals as the earth point for measuring the
respective check terminals.
E601 (H-4), E604 (C-9), E605 (N-2), E606 (C-7),
E607 (A-11), E608 (B-5), E609 (L-4), E610 (N-6),
E611 (E-4), E622 (F-7), E623 (A-2), E625 (J-6),
E626 (F-7), E627 (F-10) : GND terminals
Use these terminals as the earth point for measuring the
respective check terminals.
TP201 (C-3), TP603 (A-5) :
+
+
+
+
+1.5 V check terminal
+1.5 V measuring terminal.
TP301 (E-3), TP602 (A-5) :
+
+
+
+
+1.8 V check terminal
+1.8 V measuring terminal.
TP401 (G-3), TP604 (A-4) :
+
+
+
+
+2.5 V check terminal
+2.5 V measuring terminal.
TP501 (J-3), TP605 (A-4) :
+
+
+
+
+3.3 V check terminal
+3.3 V measuring terminal.
TP601 (A-4) :
+
+
+
+
+12 V check terminal
+12 V measuring terminal.