Intel 2 Duo T7600 LE80537GF0534M User Manual
Product codes
LE80537GF0534M
Datasheet
33
Electrical Specifications
NOTES:
1.
1.
Each processor is programmed with a maximum valid voltage identification value (VID), which is set at
manufacturing and cannot be altered. Individual maximum VID values are calibrated during manufacturing
such that two processors at the same frequency may have different settings within the VID range. Note
that this differs from the VID employed by the processor during a power management event (Intel Thermal
Monitor 2, Enhanced Intel SpeedStep Technology, or Enhanced Halt State).
manufacturing and cannot be altered. Individual maximum VID values are calibrated during manufacturing
such that two processors at the same frequency may have different settings within the VID range. Note
that this differs from the VID employed by the processor during a power management event (Intel Thermal
Monitor 2, Enhanced Intel SpeedStep Technology, or Enhanced Halt State).
2.
The voltage specifications are assumed to be measured across V
CC_SENSE
and V
SS_SENSE
pins at socket with
a 100-MHz bandwidth oscilloscope, 1.5-pF maximum probe capacitance, and 1-MΩ minimum impedance.
The maximum length of ground wire on the probe should be less than 5 mm. Ensure external noise from
the system is not coupled in the scope probe.
The maximum length of ground wire on the probe should be less than 5 mm. Ensure external noise from
the system is not coupled in the scope probe.
3.
Specified at 105 °C T
J
.
4.
Specified at the nominal V
CC
.
5.
Measured at the bulk capacitors on the motherboard.
6.
V
CC,BOOT
7.
Based on simulations and averaged over the duration of any change in current. Specified by design/
characterization at nominal V
characterization at nominal V
CC
. Not 100% tested.
8.
This is a power-up peak current specification, which is applicable when V
CCP
is high and V
CC_CORE
is low.
9.
This is a steady-state I
CC
current specification, which is applicable when both V
CCP
and V
CC_CORE
are high.
10.
The maximum delta between Intel Enhanced Deeper Sleep and LFM on the processor will be lesser than or
equal to 300 mV.
equal to 300 mV.
11.
The I
CCDES
(max) specification of 60 A is for Intel® Core
™
2 Extreme processors only.
I
AH,
I
SGNT
I
CC
Auto-Halt & Stop-Grant
HFM
SuperLFM
SuperLFM
—
—
29.7
16.7
16.7
A
3, 4, 10
I
SLP
I
CC
Sleep
HFM
SuperLFM
SuperLFM
—
—
28.8
16.5
16.5
A
3, 4, 10
I
DSLP
I
CC
Deep Sleep
HFM
SuperLFM
SuperLFM
—
—
26.8
16.0
16.0
A
3, 4, 10
I
DPRSLP
I
CC
Deeper Sleep (C4)
—
—
12.2
A
3, 4
I
DC4
I
CC
Intel Enhanced Deeper Sleep State
—
—
11.7
A
3, 4
I
PPWDN
I
CC
Deep Power Down Technology State (C6)
—
—
11.0
A
3, 4
dI
CC/
DT
V
CC
Power Supply Current Slew Rate at
Processor Package Pin
—
—
600
mA/µs
5, 7
I
CCA
I
CC
for V
CCA
Supply
—
—
130
mA
I
CCP
I
CC
for V
CCP
Supply before V
CC
Stable
I
CC
for V
CCP
Supply after V
CC
Stable
—
—
4.5
2.5
2.5
A
A
A
8
9
9
Table 6.
Voltage and Current Specifications for the Dual-Core, Extreme Edition
Processors (Sheet 2 of 2)
Symbol
Parameter
Min
Typ
Max
Unit
Notes