NuTone 62BK244CBK(X) User Manual

MODEL

:   

62BK244CBK(X), 62BK244CCN(X),

 

   62BK244CCY(X), 62BK244CMP,

 

   62BK244TBK(X), 62BK244TCY(X),

 

   62BK244TGK(X), 62BK244TMP

 

  RECESSED MOUNTED,  STEEL    

 BATH CABINETS

 

 

1.  Carefully remove all packing material.  Place hardware  

 

 

packages, shelves and door aside until needed.  Hardware  

 

 

and shelves are located in the fi llers identifi ed by “Hardware  

  Enclosed” 

tape.

 

2.  Determine desired location of cabinet on wall.  Mark wall to  

 

 

show wall opening size (see dimension chart).  Generally, the  

 

 

recommended height to the center of the cabinet is 64” from  

 

 

the fl oor.   (Fig. 1)

 

3.  CAUTION:  Wall studs, plumbing or electrical lines that  

 

 

interfere must be removed or relocated.  Cut wall opening,  

 

 

being careful not to damage the surrounding wall surface.   

 

 

Insert framing to support all plaster board edges.

 

4.  Prepare the mounting screws by placing the screws into the  

 

 

plastic bases.  (Fig. 2)

 

5.  Note:  For ease of installation, an additional person is   

 

 

recommended.  Insert cabinet into wall opening. (Fig.3)   

 

 

Ensure the cabinet is plumb and level.  If necessary use a  

 

 

carpenter’s level and shim corners of cabinet.  Secure to wall  

 

 

studs through the four (4) mounting holes inside cabinet,  

 

 

using the screws that have been placed into the plastic  

 

 

bases.  (Fig. 4)  Do not over tighten the mounting screws as  

 

 

the body side wall may bend and prevent proper shelf     

 

 

installation.  Only tighten screws until they are fl ush with the  

  body.
 

6.  Snap the screw covers over the screw bases.  (Fig.5)

 

 

1.  Remove hinges and screws from hardware bag.  Mount  

 

 

hinge unit on door as shown in Fig. 6 securing with screws  

  provided.
 

2.  Install the door by inserting door side of the hinge into the  

 

 

bracket on the body shown in Fig. 7.

 

3.  Check door for proper alignment.  If the door needs to be  

 

 

adjusted please refer to the adjustment procedures in Fig. 8.   

 

 

 

 

1.  Select where you want the shelves to be placed.

 

2.    Insert two (2) shelf brackets at each end of the shelf location.   

  (Fig. 

9).

 

3.    Set shelves in place on the shelf brackets, pressing down  

 

 

on the shelf to lock in place.  (Fig. 9).

 

4.  Remove hole plugs from hardware bag and place in    

 

 

remaining holes.  (Fig. 10).

 

5.  Remove bumpers from hardware bag and position to body.   

 

 

(Refer to Service Parts Drawing - Key No. 9 for bumper

  locations). 

 
 

 

 

 

Fig. 2

For help, call us toll 

free!

1-800-325-8351

      MODEL 

 

WALL OPENING 

OVERALL SIZE

         NO.  

   

   W      H      D            W     H      D

62BK244CBK(X)  

14

1

/

4

    24    4   

  16

1

/

2

  26

1

/

2

  5

1

/

4

62BK244CCN(X)  

14

1

/

4

    24    4   

  16

1

/

2

  26

1

/

2

  5

1

/

4

62BK244CCY(X)  

14

1

/

4

    24    4          16

1

/

2

  26

1

/

2

  5

1

/

4

62BK244CMP  

 14

1

/

4

    24    4   

  16

1

/

2

  26

1

/

2

  5

1

/

4

62BK244TBK(X)  

14

1

/

4

    24    4   

  16

1

/

2

  26

1

/

2

  5

1

/

4

62BK244TCY(X)  

14

1

/

4

    24    4            16

1

/

2

  26

1

/

2

  5

1

/

4

62BK244TGK(X)  

14

1

/

4

    24    4            16

1

/

2

  26

1

/

2

  5

1

/

4

62BK244TMP  

 14

1

/

4

    24    4            16

1

/

2

  26

1

/

2

  5

1

/

4

 

 

Fig. 1

Approx.
64" to 
Floor

W

D

H

Insert screw
through clear 
plastic base

Fig. 3

Mounting
Screws

Mounting
screw into 
mounting 
hole

Fig. 4

Wall
Opening

Cabinet
Body

 Snap on Cover

Cover

Base

Screw

Fig. 5

Hinge Mounted 
      to Door

Fig. 6

Hook bottom of
hinge into place
on the bracket

Press down
on hinge until it
clips in place

Hinge Mounted 
to Cabinet

Fig. 7

Door Adjustment

This screw for 
up and down
adjustments

This screw
for depth
adjustments

This screw
for left and right
adjustments 

Fig. 8

Fig. 9

Fig. 10