American Standard 7048.401 Leaflet
Perimeter
of sink
of sink
Cutout
Perimeter
of sink
of sink
Cutout
CHANDLER™ KITCHEN SINK
w/DRAINBOARD
w/DRAINBOARD
MODEL 7048.401 RIGHT HAND DRAIN BOARD
MODEL 7048.501 LEFT HAND DRAIN BOARD
MODEL 7048.501 LEFT HAND DRAIN BOARD
Installation Instructions
7 9 0 7 6 0 - 1 0 0
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
1
2
BEFORE YOU BEGIN...Unpack new sink and
inspect carefully for damage. Replace the sink
in its original packing carton to protect it until
you are ready to begin installation.
inspect carefully for damage. Replace the sink
in its original packing carton to protect it until
you are ready to begin installation.
3
Drill a clearance
hole inside the
cutout line
as marked on
the countertop.
NOTE: The drain-
board is not
part of the cut
out and sits above the countertop.
hole inside the
cutout line
as marked on
the countertop.
NOTE: The drain-
board is not
part of the cut
out and sits above the countertop.
Mount the faucet
and drain assembly
on the sink
following the
manufacturer's
instructions.
and drain assembly
on the sink
following the
manufacturer's
instructions.
Cut opening on
cut line inside the
perimeter of bowl
shape.
cut line inside the
perimeter of bowl
shape.
AFTER THE CUTOUT IS DRAWN...
Certified to comply with ANSI Z124.6
Observe local plumbing and building codes.
Observe local plumbing and building codes.
™
CUTOUT DIMENSIONS FOR SINK
Recommended Tools & Materials
Putty Knife
Pipe Wrench
Channel Locks
Phillips Screwdriver
Regular Screwdriver
Adjustable Wrench
Drill
Pipe Wrench
Channel Locks
Phillips Screwdriver
Regular Screwdriver
Adjustable Wrench
Drill
Locate and mark center lines of sink on countertop.
Provide proper clearance under the countertop for
the faucet supply lines and the structural parts of the
cabinet.
Provide proper clearance under the countertop for
the faucet supply lines and the structural parts of the
cabinet.
By using the diagram below and measuring your sink,
draw the outline of the sink onto the countertop. This
is not the cutting outline.
draw the outline of the sink onto the countertop. This
is not the cutting outline.
Basin Wrench
Saber Saw
Plumbers' Putty or
Caulking
Tubing Cutter
Tape Measure
Hacksaw
Saber Saw
Plumbers' Putty or
Caulking
Tubing Cutter
Tape Measure
Hacksaw
M
A D E W I T H
32"
19-1/2"
19-1/2"
21"
10-1/2"
21" Radius
21" Radius
35"
1-1/2"
CENTER LINE
SINK
OUTLINE
OUTLINE
RIGHT
HAND
DRAIN
BOARD
C/L OF
DOUBLE
BOWL
DOUBLE
BOWL
1/2"TYP.
CUTTING
LINE
(SHADED
AREA)
LINE
(SHADED
AREA)
CUTTING
LINE
LINE
CUTOUT FOR NEW INSTALLATION
MODIFICATION REQUIRED TO FIT CHANDLER SINK
INTO A STANDARD 33" X 22" SINK CUTOUT
NOTE: ALLOW ROOM ON EITHER SIDE OF SINK
DEPENDING ON RIGHT OR LEFT HAND DRAIN BOARD
10-1/2"
21"
22"
49-1/2"
35"
32"
Product names listed herein are trademarks of American Standard Inc. unless otherwise noted.
Corian
®
Dupont registered trademark
© American Standard Inc. 2000
Right Hand
Drain Board
Drain Board
Left Hand
Drain Board
Drain Board
Right Hand Shown