American Standard 2787 User Manual
7 3 0 4 9 8 - 1 0 0 R e v . A
6
8
7
INSTALL TOILET
a.
Position toilet squarely to wall and, with a rocking motion,
press bowl down fully on wax ring and flange. Alternately
tighten nuts until toilet is firmly seated on floor.
tighten nuts until toilet is firmly seated on floor.
CAUTION:
DO NOT OVERTIGHTEN NUTS
OR BASE MAY BE DAMAGED!
b.
Install caps on washers. (If necessary, cut bolt height to size
before installing caps.)
c.
Smooth off the bead of sealant around base. Remove excess
sealant.
INSTALL TOILET SEAT Install toilet seat in accordance with manufacturer's directions.
CLOSET FLANGE
CLOSET BOLT
NUT
WASHER
BOLT CAP
!
- 2 -
9a
9b
Before continuing, determine the type of water supply connecation you have from
the chart below and use the appropriate assembly parts required to properly
reconnect the water supply. DO NOT use plumber's putty to seal these fittings.
the chart below and use the appropriate assembly parts required to properly
reconnect the water supply. DO NOT use plumber's putty to seal these fittings.
CAUTION: DO NOT USE
CONE WASHER WITH
PLASTIC SUPPLY LINE.
CONE WASHER WITH
PLASTIC SUPPLY LINE.
These parts must be used as
illustrated to insure water-tight
connection. Use of existing
coupling nut may result in
water leakage. Water supply
tube or pipe must extend at
least 1/2" inside threaded
shank of valve (does not apply
to flanged tubing).
illustrated to insure water-tight
connection. Use of existing
coupling nut may result in
water leakage. Water supply
tube or pipe must extend at
least 1/2" inside threaded
shank of valve (does not apply
to flanged tubing).
Use existing
coupling nut
and washer.
coupling nut
and washer.
Use existing spiral
cone washer.
Fluidmaster cone
washer may not
seal completely on
spiral type supply
line.
cone washer.
Fluidmaster cone
washer may not
seal completely on
spiral type supply
line.
Captive cone
washers already
included. No
additional washers
needed.
washers already
included. No
additional washers
needed.
CAUTION: Overtightening of
LOCK NUT or COUPLING NUT
could result in breakage and
potential flooding.
LOCK NUT or COUPLING NUT
could result in breakage and
potential flooding.
METAL/COPPER
FLARED TUBING
METAL FLANGED
TUBING
METAL SPIRAL
TUBING
VINYL/BRAIDED
CONNECTOR
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
COUPLING
NUT
NUT
COUPLING
NUT
NUT
EXISTING
COUPLING
NUT
COUPLING
NUT
COUPLING
NUT
NUT
WATER
SHUT-OFF
SHUT-OFF
WATER
SHUT-OFF
SHUT-OFF
WATER
SHUT-OFF
SHUT-OFF
WATER
SHUT-OFF
SHUT-OFF
CONE
WASHER
WASHER
EXISTING
CONE
WASHER
CONE
WASHER
EXISTING
WASHER
WASHER
With correct washers in place
(see Step 9a), tighten
COUPLING NUT 1/4 turn beyond
hand tight. DO NOT
OVERTIGHTEN.
(see Step 9a), tighten
COUPLING NUT 1/4 turn beyond
hand tight. DO NOT
OVERTIGHTEN.
RUBBER
GASKET
GASKET
TANK MTG.
BOLTS PRE-
INSTALLED
BOLTS PRE-
INSTALLED
NUT
WASHER
INSTALL TANK
a.
Install large rubber gasket over threaded
outlet on bottom of tank and lower tank onto
bowl so that tapered end of gasket fits
evenly into bowl water inlet opening, and
tank mounting bolts go through mounting
holes. Secure with metal washers and nuts.
bowl so that tapered end of gasket fits
evenly into bowl water inlet opening, and
tank mounting bolts go through mounting
holes. Secure with metal washers and nuts.
b.
With tank parallel to wall, alternately tighten
nuts until tank is snugged down evenly
against bowl surface.
against bowl surface.
!
CAUTION:
DO NOT OVERTIGHTEN NUTS MORE
THAN REQUIRED FOR A SNUG FIT!