American Standard 2373.821 User Manual

Insert SPOUT (1) and CABLE CONNECTOR (14) through center hole, making sure

the SPOUT ESCUTCHEON (2) and SEAL WASHER (3) are properly seated.
Assemble RUBBER WASHER (4), BRASS WASHER (5) and LOCKNUT (6) onto SPOUT

SHANK (7) from under side of sink . Make sure SPOUT (1) is centered in the mounting

hole and the slot in the BRASS WASHER (5) faces toward the rear of the sink.

Tighten LOCKNUT (6) firmly. Fig. A.

Tighten LOCKNUT (11) with WRENCH (8) (supplied) to secure VALVE

BODY (13). Repeat above steps for opposite VALVE BODY (13A).

Install LOCKNUT (11) and RUBBER WASHER (12) onto VALVE BODY (13).

From under side of mounting surface, install VALVE BODY (13) through valve

mounting holes. Threads of VALVE BODY (13) should extent at least 5/16

of a inch above mounting surface top. Fig. B. Thread DECK ADAPTER (10)

onto VALVE BODY (13) until snug against internal stop. If necessary, adjust

LOCKNUT (11).

Certified to comply with ANSI A112.18.1

Place RUBBER RING (9) into DECK ADAPTER (10).

Adjustable Wrench

 Screwdriver

Channel Locks

Tubing Cutter

Connect HOT water supply to inlet of left SHANK and COLD

water supply to right SHANK using sealant, appropriate

connectors, and COUPLING NUTS.

Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to

waste outlet.

Thread TEE BODY (4) to SPOUT SHANK (5).

Thread HOSE CONNECTOR (6, 6A) to VALVE CONNECTIONS (7, 7A).

With HANDLES (1) in OFF position, turn on WATER

SUPPLIES (2) and check all connections for leaks.

Remove AERATOR (3).

Operate both HANDLES (1) to flush water

lines thoroughly.

Replace AERATOR (3).

Connect water supply to VALVE BODIES (1,1A) with 1/2" IPS FLEXIBLE

SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3). Use

adjustable wrench to tighten connections. Do not over tighten.

Be careful not to kink copper supply when bending. Use tubing

cutter to cut to proper length.

 

Operate POP-UP KNOB (5) and fill Sink with water. Check

that DRAIN STOPPER (4) makes a good seal and retains

water in Sink. If STOPPER (4)  does not seal properly, please

refer to “Troubleshooting Guide” in these instructions.

Release POP-UP KNOB (5) down and check all drain

connections and "P" trap for leaks.        Tighten

if necessary.

Thread CABLE CONNECTOR (1) clockwise

onto DRAIN BODY CONNECTION (2) and

hand tighten. Fig. A.

Your new POP-UP DRAIN installation is

now complete. Fig. B.

Note: Tailpeice on pop-up drain is 1-1/4” O.D.

Fig. B.

Fig. A.

Operate LIFT KNOB (1) to verify that STOPPER (2) opens and

closes.

Note: If STOPPER (2) does not open and close properly then refer

to the “troubleshooting section” of these instructions.

Fig. B.

Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.

Look at the area on the Drain Body where the Cable was attached and locate the component labeled

as “Cam”  and “Cam Cap” in the illustration. Fig. B.

Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D.

Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E.

The Stopper can now be removed by lifting it out of the Drain. Fig. F.

     • Follow CABLE ADJUSTMENT PROCEDURE.

     • Follow CABLE ADJUSTMENT PROCEDURE.

     • Follow STOPPER REMOVAL PROCEDURE.

     • Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode. 

                                                                          

Fig. B.

Fig. A.

Fig. E.

Fig. F.

Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.

Look at the area on the Drain Body where the Cable was attached and locate the component labeled as

“Cam” in the illustration. Fig. B.

Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the

Stopper should be in the UP position. Fig. B, C. 

Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C.

Re-attach the Cable to the Drain Body Connection (2) by threading the Cable Connector (1) clockwise onto the

Drain Body Connection (2) and hand-tighten. Fig. A.

Look at the Plastic Loop at the bottom of the Stopper and notice

that the Loop is on one side of the Stopper. Fig. G.

To install the stopper in “Locked” mode, insert the Stopper into

the Drain so that the Plastic Loop is facing toward the rear of the

Sink and the American Standard logo is facing front. Rotate

Stopper slightly if necessary so that the Stopper slides all the

way down.Fig. G.

Re-install the Cam into the Drain, rotating the Cam if necessary

to make sure it is fully inserted. Fig. J.

Re-install the Cam Cap, making sure the guide teeth are facing

outward. If the Cam Cap does not “snap” into place, then rotate

the Cam to make sure it is fully inserted. Fig. K.

Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in

Troubling Shooting Guide to complete installation. Stopper will be

in “Locked” mode and not be removable.

Look at the Plastic Loop at the bottom of the Stopper and notice

that the Loop is on one side of the Stopper. Fig. H.

To install the stopper in “Unlocked” mode, insert the Stopper into

the Drain so that the Plastic Loop is facing toward the front of the

Sink and the American Standard logo is facing rear. Rotate Stopper

slightly if necessary so that the Stopper slides all the way down.

Fig. H.

Re-install the Cam into the Drain, rotating the Cam if necessary

to make sure it is fully inserted. Fig. J.

Re-install the Cam Cap, making sure the guide teeth are facing

outward. If the Cam Cap does not “snap” into place, then rotate

the Cam to make sure it is fully inserted. Fig. K.

Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in

“Troublingshooting Guide” to complete installation. Stopper will be

in “Unlocked” mode and removable

.

Fig. J.

Fig. K.

Fig. A.

Fig. B.

Fig. H.

Fig. G.

Fig. D.

Fig. C.

LIFT ROD

EXTENSION ROD

DRAIN STOPPER

TAILPIECE INSERT

CLIP

PIVOT ROD KIT

COMPLETE

DRAIN ASSEMBLY

TAILPIECE

2" FLANGE KIT

M 9 6 8 3 0 1   R e v.   1 . 3

M 9 6 8 3 0 1   R e v.   1 . 3

M 9 6 8 3 0 1   R e v.   1 . 3

M 9 6 8 3 0 1   R e v.   1 . 3

M 9 6 8 3 0 1   R e v.   1 . 3

M 9 6 8 3 0 1   R e v.   1 . 3

M 9 6 8 3 0 1   R e v.   1 . 3

Fig. A.

Fig. B.

SEAL

SPOUT ESCUTCHEON

SUPPLY NUT

SPOUT

MOUNTING KIT

TEE & HOSE KIT

Replace the "YYY" with

appropriate finish code

CARTRIDGE

VALVE MOUNTING KIT

SPOUT KIT

CHROME

POLISHED NICKEL

BLACKENED BRONZE

POLISHED BRASS

SATIN NICKEL 

002

008

068

099

295

AERATOR

DECK ADAPTER KIT

HANDLE SCREW

STEM ADAPTER

LEVER HANDLE

ASSEMBLY

CROSS HANDLE

ASSEMBLY

Replace SPRAY (5) and operate handles several times

from OFF to ON position. Do not force, handles turn only 90˚.

SPRAY (5) may accumulate dirt causing distorted

and reduced water flow. Unscrew and remove

SPRAY (5) and rinse clean.

To change direction of handle rotation, 

proceed as follows

:

Turn valve to OFF position.Unthread HANDLE

BASE (1) from DECK ADAPTER (2).

Pull HANDLE ASSEMBLY off VALVE STEM (3).

Remove SPRING CLIP (4). Lift STOP WASHER (5),

turn 90° and replace. Replace SPRING CLIP (4).

Find correct position of HANDLE ASSEMBLY by

adjusting male teeth on VALVE STEM (3) to

female teeth in HANDLE.

Thread HANDLE ASSEMBLY onto DECK ADAPTER

(2) until snug against mounting surface.

Push ADAPTER (1) on VALVE STEM (2), so that the hole of the

ADAPTER (1) without a spline is facing up. See figure "A". Tighten

STEM SCREW (3) to secure ADAPTER (1). 

Find correct position of LEVER HANDLE ASSEMBLY (4) or CROSS

HANDE ASSEMBLY (5) by adjusting male teeth on ADAPTER (1) to

female teeth in HANDLE (4, 5).

Thread LEVER HANDLE ASSEMBLY (4) or CROSS HANDE ASSEMBLY

(5) onto DECK ADAPTER (6) until snug against mounting surface.

POP-UP KNOB (1) must be fully down. Fig. B.  

Check DRAIN FLANGE in SINK to ensure that

WHITE FOAM GASKET (3) is fully compressed

and not visible. Fig. A.

Thread FLANGE (1) counter-clockwise and remove

FLANGE (1) and FOAM GASKET (2) from drain

body. Fig. A.
Thread LOCKNUT (3) clock-wise to bottom of

drain body. Push GASKET (4) down against

LOCKNUT (3). Fig. B.

Tighten TAILPIECE (4) on DRAIN BODY before

installing DRAIN BODY. Fig. B.

Remove CLEAR PLASTIC COVER (1).

Remove CARDBOARD SPACER (2) from under

DRAIN POP-UP (3).

Tighten LOCKNUT (1) firmly with Adjustable

Wrench or Channel Locks.

From under side of SINK

install DRAIN BODY (1) up

through drain outlet.

Note: No plumber’s putty

or caulk is required.

The CABLE ATTACHMENT

POINT (2) must face towards

the rear of the SINK.

Install FOAM GASKET (3) and

FLANGE (4) onto drain body

from above SINK and tighten

FLANGE (4) firmly.

Fig. A.

Fig. B.

Fig. A.

Fig. B.

HOT LINE FOR HELP

For toll-free information and answers to your questions, call:

1 (800) 442-1902

Weekdays 8:00 a.m. to 6:00 p.m. EST

IN CANADA  1-800-387-0369   (TORONTO 1-905-306-1093)

Weekdays 8:00 a.m. to 7:00 p.m. EST

Product names listed herein are trademarks of American Standard Inc.

© American Standard Inc. 2003

IN MEXICO  01-800-839-12-00

LIFT ROD AND KNOB

*Your new American Standard faucet is designed to work only with the Speed Connect drain. 

•  Fewer parts, installs in less time

•  Never needs adjustment

•  Guaranteed to seal properly the first time, every time.

CAM ASSEMBLY

CABLE ASSEMBLY

 DRAIN ASSEMBLY

STOPPER

ASSEMBLY

FLANGE

ASSEMBLY

DRAIN MOUNTING KIT

TAILPIECE

CAM SEAT INSERT

TAILPIECE INSERT

6” TAILPIECE