American Standard 2405.016 User Manual
7 3 0 7 2 9 - 1 0 0
5
POSITION TOILET ON FLANGE
a.
a.
Unplug floor waste opening and install toilet on closet flange so
bolts project through mounting holes.
bolts project through mounting holes.
b.
Loosely install retainer washers and nuts. Side of washers
marked "THIS SIDE UP"
marked "THIS SIDE UP"
must
face up!
CLOSET
BOLT
NUT
TAPERED
WASHER
WASHER
FLANGE
6
8
7
INSTALL TOILET
a.
Position toilet squarely to wall and, with a rocking motion, press bowl
down fully on wax ring and flange. Alternately tighten nuts until toilet is
firmly seated on floor.
firmly seated on floor.
CAUTION: DO NOT OVERTIGHTEN NUTS
OR BASE MAY BE DAMAGED!
b.
Install caps on washers. (If necessary, cut bolt height to size before
installing caps.)
c.
Smooth off the bead of sealant around base. Remove excess sealant.
CLOSET FLANGE
CLOSET
BOLT
BOLT
NUT
WASHER
BOLT CAP
!
- 2 -
9a
9b
CAUTION:
DO NOT USE
CONE WASHER
WITH PLASTIC
SUPPLY LINE.
DO NOT USE
CONE WASHER
WITH PLASTIC
SUPPLY LINE.
CAUTION:
Overtightening of
LOCK NUT or
COUPLING NUT
could result in
breakage and
potential flooding.
Overtightening of
LOCK NUT or
COUPLING NUT
could result in
breakage and
potential flooding.
These parts must be
used as illustrated to
insure water-tight
connection. Use of
existing coupling nut
may result in water
leakage. Water supply
tube or pipe must extend
at least 1/2" inside
threaded shank of valve
(does not apply to
flanged tubing).
used as illustrated to
insure water-tight
connection. Use of
existing coupling nut
may result in water
leakage. Water supply
tube or pipe must extend
at least 1/2" inside
threaded shank of valve
(does not apply to
flanged tubing).
Use existing
coupling nut
and washer.
coupling nut
and washer.
Use existing spiral
cone washer.
Fluidmaster cone
washer may not
seal completely on
spiral type supply
line.
cone washer.
Fluidmaster cone
washer may not
seal completely on
spiral type supply
line.
Captive cone
washers already
included. No
additional washers
needed.
washers already
included. No
additional washers
needed.
METAL/COPPER
FLARED TUBING
METAL FLANGED
TUBING
METAL SPIRAL
TUBING
VINYL/BRAIDED
CONNECTOR
LOCK NUT
LOCK NUT
LOCK NUT
LOCK NUT
COUPLING
NUT
NUT
COUPLING
NUT
NUT
EXISTING
COUPLING
NUT
COUPLING
NUT
COUPLING
NUT
NUT
WATER
SHUT-OFF
SHUT-OFF
WATER
SHUT-OFF
SHUT-OFF
WATER
SHUT-OFF
SHUT-OFF
WATER
SHUT-OFF
SHUT-OFF
CONE
WASHER
WASHER
EXISTING
CONE
WASHER
CONE
WASHER
EXISTING
WASHER
WASHER
RUBBER
GASKET
GASKET
TANK MTG.
BOLTS PRE-
INSTALLED
BOLTS PRE-
INSTALLED
NUT
WASHER
INSTALL TANK
a.
Install large rubber gasket over threaded outlet on bottom of tank
and lower tank onto bowl so that tapered end of gasket fits evenly
into bowl water inlet opening, and tank mounting bolts go through
mounting holes. Secure with metal washers and nuts.
into bowl water inlet opening, and tank mounting bolts go through
mounting holes. Secure with metal washers and nuts.
b.
With tank parallel to wall, alternately tighten nuts until tank is
snugged down evenly against bowl surface.
!
CAUTION:
DO NOT OVERTIGHTEN NUTS MORE
THAN REQUIRED FOR A SNUG FIT!
With correct washers in place (see Step 9a),
tighten COUPLING NUT 1/4 turn beyond hand
tight. DO NOT OVERTIGHTEN.
tighten COUPLING NUT 1/4 turn beyond hand
tight. DO NOT OVERTIGHTEN.
INSTALL TOILET SEAT
Install toilet seat in accordance with manufacturer's directions.
Install toilet seat in accordance with manufacturer's directions.
Before continuing, determine the type of
water supply connecation you have from the
chart below and use the appropriate
assembly parts required to properly
reconnect the water supply. DO NOT use
plumber's putty to seal these fittings.
water supply connecation you have from the
chart below and use the appropriate
assembly parts required to properly
reconnect the water supply. DO NOT use
plumber's putty to seal these fittings.