American Standard 4771.222 SER. Leaflet
M 9 6 8 1 4 5 D
1
INSTALL FAUCET
Turn off hot and cold water supplies before beginning.
CAUTION
Place faucet in position on sink.
Assemble and tighten LOCKNUTS from underside of SINK.
Connect the HOT water supply to the left SHANK and the
COLD water supply to the right SHANK using sealant,
appropriate connectors, and COUPLING NUTS.
COLD water supply to the right SHANK using sealant,
appropriate connectors, and COUPLING NUTS.
To install SPRAY:
Screw SPOUT onto BODY.
LOCKNUT
HOT
COLD
COUPLING
NUT
SPRAY HOSE
COUPLING NUT
PUTTY
BODY
SINK
HOSE
SHANK
W I N G
N U T
S P R A Y
H O L D E R
Place the HOLDER into the appropriate mounting hole.
Assemble the SPRAY HOLDER WING NUT onto the shank
of SPRAY HOLDER from below and tighten.
Assemble the SPRAY HOLDER WING NUT onto the shank
of SPRAY HOLDER from below and tighten.
From underneath sink, attach COUPLING NUT of SPRAY HOSE
to HOSE SHANK. Tighten COUPLING NUT firmly.
to HOSE SHANK. Tighten COUPLING NUT firmly.
Feed SPRAY HOSE through HOLDER so SPRAY sits in HOLDER.
S P R A Y
H O S E
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .
A m e r i c a n S t a n d a r d I n c . 1 9 9 8
C
Unscrew SPRAY CAP.
SPRAY
CAP
TEST INSTALLED FAUCET
2
Remove AERATOR.
With handle in OFF position, turn on water supplies and check
all connections for leaks.
all connections for leaks.
Operate SPRAY (if present).
Operate both handles to flush water lines thoroughly.
Turn handles into OFF position and replace AERATOR.
Check alignment, if not satisfactory
aligned;
aligned;
Push out ADAPTER carefully.
Turn ADAPTER either 45˚ or 90˚
so that male square on
ADAPTER catches different
female square in HANDLE BASE.
so that male square on
ADAPTER catches different
female square in HANDLE BASE.
Assemble and tighten
MOUNTING SCREW.
MOUNTING SCREW.
Push INDEX CAP in top of
HANDLE.
HANDLE.
SERVICE
Handle alignment.
3
To change direction of handle rotation,
proceed as follows:
proceed as follows:
AERATOR may accumulate dirt causing distorted and reduced
water flow. Remove AERATOR and rinse clean.
water flow. Remove AERATOR and rinse clean.
If spout drips, operate handles several times from OFF to ON
position. Do not force - handles turn only 90
position. Do not force - handles turn only 90
°
.
SPRING
CLIP
STOP
WASHER
90
°
Turn valve to OFF position.
Pull out INDEX CAP and remove
HANDLE SCREW.
Pull off HANDLE BASE and remove
ADAPTER.
Remove SPRING CLIP.
Lift STOP WASHER, turn 90
Pull out INDEX CAP and remove
HANDLE SCREW.
Pull off HANDLE BASE and remove
ADAPTER.
Remove SPRING CLIP.
Lift STOP WASHER, turn 90
°
and replace.
Replace SPRING CLIP.
Reinstall HANDLE.
Reinstall HANDLE.
VALVE
STEM
FEMALE SQUARE
IN HANDLE BASE
IN HANDLE BASE
HANDLE
ADAPTER
SQUARE
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 (800) 442-1902
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST