American Standard 7820.400 Leaflet

7 3 0 8 3 7 - 1 0 0   R e v .   A

Adjustable Wrench

Channel Locks

Putty Knife

Level

Basin Wrench

Plumbers' Putty 

Tubing Cutter

Tape
Measure

Pipe Wrench

Silicone Caulk

If inspection of this American Standard plumbing product, within one year after its initial purchase, confirms that it is defective in materials or workmanship, American Standard 

will repair or, at its option, exchange the product for a similar model. 

This warranty does not apply to local building code compliance.  Since local building codes vary considerably, the purchaser of this product should check with a local building 

or plumbing contractor to insure local code compliance before installation.

This warranty shall be void if the product has been moved from its initial place of installation; if it has been subjected to faulty maintenance, abuse, misuse, accident or other 

damage; if it was not installed in accordance with American Standard's instructions; or if it has been modified in a manner inconsistent with the product as shipped by American 
Standard.

American Standard's option to repair or exchange the product under this warranty does not cover any labor or other costs of removal or installation, nor shall American 

Standard be responsible for any other incidental or consequential damages attributable to a product defect or to the repair or exchange of a defective product, all of 
which are expressly excluded from this warranty. (Some states or provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may not apply to 
you.)

This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to province, in which case this warranty does not 

affect such statutory rights.

For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the product was purchased, or that a service request 
(including a description of the product  model and of the defect) be sent  to the following address:

When cleaning your vanity top, wash it with mild, soapy water, rinse 
thoroughly with clear water and dry with a soft cloth.  Avoid abrasive 
detergents, disinfectants, or cleaning products in aerosol cans.   

Mount the drain assembly (not included) on 
the sink.  Be certain to apply a bead of 
sealing putty on the underside of the drain 
(Part "A") in order to ensure a watertight seal 
between the sink and drain.  Remove excess 
putty after installing the drain on the sink.  

Apply a bead of silicone adhesive to the rim 
of the vanity.  Place the top centered left to 
right on the vanity and with the back edge of 
the top even with the rear of the vanity. Apply 
a bead of silicone along the top back edge of 
the vanity top and the wall. Clean up any 
excess silicone.

Connect the trap to the drain assembly hand 
tight to check alignment.  It may be necessary 
to cut off part of the tailpiece (area "B") or part 
horizontal leg of the trap (area "C").  

Connect hot and cold supply lines to the shut 
off valves.  Tighten trap joints for watertight 
assembly.

™

To maintain the beauty of the finish, avoid placing the furniture in direct sunlight, as sunlight causes fading.  Also avoid extreme changes in 
temperature by arranging furniture away from radiators, heat and air vents, and air conditioning units.  Avoid placing furniture directly under windows.

Thank you for selecting our products...products which have been the benchmarks of fine quality for over 100 years. To help insure that the installation 
process will proceed smoothly, please read these instructions carefully before you begin. Also, review the recommended tools and materials list; 
carefully unpack and examine your new plumbing fixture.

American Standard Inc.

P.O. Box 6820

Piscataway, New Jersey 08855

Attention: Director of  Consumer Affairs

For residents of the United States, warranty information may also be

obtained by calling the following toll free number: (800) 442-1902

American Standard

2480 Stanfield Rd.  

Mississauga, Ontario 

Canada L4Y 1S2

Toll Free:  (800) 387-0369

Customer Service Manager 

Ideal Standard, S.A. de C.V.

Via Morelos #330

Col. Santa Clara

Ecatepec 55540 Edo. Mexico

FINISHED

WALL

OR 

SPLASH BACK

22-7/8"

(581mm)

22"

(559mm)

1-3/4"

DIA.

4"

(102mm)

7820.400

MODEL

4-1/2"

(114mm)

10-1/8"

(257mm)

13-3/4"

(349mm)

1-3/4"

(44mm)

FINISHED FLOOR

 

8"

(203mm)

1-1/4" O.D. TAILPIECE

1-1/4"
O.D. WASTE

SUPPLIES

AS REQ'D

11-1/4"

(286mm)

8"

(203mm)

*33-1/2"

(851mm)

31-1/8"

(791mm)

*

*

SUGGESTED 
DIMENSIONS 

*