Manualsbrain.com
  1. Manuals
  2. Brands
  3. Panasonic
  4. PT-DZ21KU
  5. User Manual

Panasonic PT-DZ21KU User Manual

Download
Page of 179
[PROJECTOR SETUP] menu
106 - ENGLISH
Settings
10)  Set [BRIGHTNESS CONTROL GAIN] 
of all projectors to 100%.
11)  Set [BRIGHTNESS CONTROL GAIN] 
of the darkest projector to 90%.
12)  Adjust [BRIGHTNESS CONTROL 
GAIN] to match the [BRIGHTNESS 
CONTROL GAIN] set to 90% of the 
other projectors.
13)  Set [MODE] in [BRIGHTNESS 
CONTROL SETUP] of all projectors to 
[AUTO], and [LINK] to [GROUP A].
14)  Select [APPLY] in [BRIGHTNESS 
CONTROL SETUP] on all projectors 
and press the <ENTER> button.
▶
z
Luminance control starts.
Note
 
z
Brightness is automatically corrected each time the 
lamp blinks when the power is switched on or off.
 
z
Adjust luminance control again when variation in 
brightness has increased or a lamp is replaced.
[STANDBY MODE]
Set the power consumption during the standby.
1)  Press ▲▼ to select [STANDBY MODE].
2)  Press ◀▶ to switch [STANDBY 
MODE].
▶
z
The setting will change as follows each time 
you press the button.
[NORMAL]
[ECO]
Note
 
z
When set to [ECO], network functions and <SERIAL 
OUT> terminal, and some RS-232C commands are 
not available during standby. The lighting for the 
connecting terminals and control panel does not 
turn on.
 
z
When an error or warning occurs, a self diagnosis 
is displayed on the control panel regardless of the 
[STANDBY MODE] setting. (
 page 25)
 
z
When set to [ECO], the time taken to start display 
may be approximately ten seconds slower than 
compared to when set to [NORMAL].
[SCHEDULE]
Set the command execution schedule for each day of 
the week.
1)  Press ▲▼ to select [SCHEDULE].
2)  Press ◀▶ to switch [SCHEDULE].
▶
z
The setting will change as follows each time 
you press the button.
[ON]
[OFF]
Note
 
z
If [SCHEDULE] is set to [ON], the setting for 
[STANDBY MODE] is automatically set to 
[NORMAL] and cannot be changed. Even if 
[SCHEDULE] is then set to [OFF] when in this 
state, the setting of [STANDBY MODE] remains at 
[NORMAL].
▶
■How to assign a program
3)  Select [ON] in Step 2), and press the 
<ENTER> button.
▶
z
The 
[SCHEDULE] screen is displayed.
4)  Select and assign program to each day 
of week.
▶
z
Press ▲▼ to select the day of week, and press 
◀▶ to select a program number.
▶
z
You can set the program from No.1 to No.7. “- 
- -” indicates that the program number has not 
been set yet.
▶
■How to set a program
You can set up to 16 commands to each program.
3)  Select [ON] in Step 2), and press the 
<ENTER> button.
▶
z
The 
[SCHEDULE] screen is displayed.
4)  Press ▲▼ to select [PROGRAM EDIT].
5)  Press ◀▶ to select a program number 
and then press the <ENTER> button.
6)  Press ▲▼ to select a command 
number and press the <ENTER> 
button.
▶
z
You can change the page using ◀▶ .
7)  Press ▲▼ to select [TIME] and press 
the <ENTER> button.
8)  Press ◀▶ to select hour and minute, 
and press ▲▼ or the number (<0> to 
<9>) buttons on the remote control 
to set a time, and press the <ENTER> 
button.
9)  Press ▲▼ to select [COMMAND].