Sunfire IV User Manual

Page of 60
User's Manual
40
CHAPTER 4
MAIN MENU
TRIMS
 
MODES
 
TONE
 
INPUTS
 
SETTINGS 
SETTINGS
MAIN ZONE
 
ZONE 2
 
SPEAKERS 
VIDEO
   
SOFTWARE
 
CONTROL
 
SPEAKER CALIBRATION
LEFT SURR BACK 
  0.0 dB
LEFT SURROUND 
  0.0 dB
LEFT SIDE AXIS 
  0.0 dB
SUBWOOFER  
  0.0 dB
GO TO LEFT MAIN
ON-THE-FLY TRIMS ZEROED
Speaker Calibration
The calibration procedure allows 
you to adjust the volume level of each 
speak er in turn until they are all equal. 
This will give you the best Home The-
ater performance. You should only do 
this calibration when you are sitting in 
your usual lis ten ing/viewing position.
Preliminary: Play a movie and adjust 
the volume for a comfortable listening 
level. The volume of the calibration test 
noise is linked to the setting of the main 
volume control, so if the test noise is 
too quiet, turn the main volume up a 
little and retry. 
 1.  Use the OSD to navigate to 
the SPEAKER CALIBRATION 
menu.
2.   Press the remote's joystick 
down to turn on the noise 
generator. While the test signal 
is playing in each speaker, its 
level can be adjusted using the 
joystick left/right buttons. Ad-
just each speaker in turn until 
they are all equal in volume.
     The best results are obtained 
if you use a Sound Pressure 
Level (SPL) Meter. This is a 
hand held meter which will ac-
curately mea sure and display 
the sound level. Adjust all of 
Speaker Calibration Menu
The range of adjustment is +/– 10 
dB (in 0.5 dB steps) for each speaker.
Record your levels here:
the speak ers until they are 
playing within 1 dB of each 
other. Without a meter, you can 
still obtain good results with 
careful listening. 
3.   Repeat the procedure several 
times for each speaker until 
you are satisfi ed they are play-
ing at the same level.
4.   Press the joystick-up to return 
to the top of the menu, and 
then press joystick-left to exit. 
The calibration noise generator 
will turn off.
 The main volume control adjusts 
the volume of all of the speakers up 
and down at the same time. They 
keep the same relative levels you set 
here, that is, they will still be playing 
as loud or as quiet as each other. 
The Dolby Digital, Dolby Pro Logic 
and DTS soundtracks are designed 
to be played back in a calibrated 
Home Theater. The sounds from each 
speaker will be at the correct relative 
levels, as the movie sound director 
designed them. Repeat the calibra-
tion if you change any external power 
amps or speakers, or if you move your 
couch relative to the speakers.
SPEAKERS
SIZE 
POSITION 
CALIBRATION 
L-R CROSSOVER 
110 HZ
C-SURR CROSSOVER 
90 HZ
SUBWFR MODE                   NORMAL
SPEAKER CALIBRATION
LEFT MAIN 
 
  0.0 dB
CENTER 
 
  0.0 dB
RIGHT MAIN   
  0.0 dB
RIGHT SIDE AXIS 
  0.0 dB
RIGHT SURROUND 
  0.0 dB
RIGHT SURR BACK 
  0.0 dB
SPEAKER
dB LEVEL
LEFT MAIN
CENTER
RIGHT MAIN
RIGHT SIDE AXIS
RIGHT SURROUND
RIGHT SURR BACK
LEFT SURR BACK
LEFT SURROUND
LEFT SIDE AXIS
SUBWOOFER