Sunfire IV User Manual
User's Manual
51
APPENDIX
The RS-232 Port
COMMAND
ASCII DATA RECEIVED
POWER TOGGLE
*111
POWER ON
*112
POWER OFF
*113
CD
*114
TAPE
*115
SAT
*116
DVD
*117
PHONO
*118
TUNER
*119
VID1
*11A
VCR
*11B
VID2
*11C
DSP MODE UP
*11D
DSP MODE DOWN
*13W
STEREO
*11E
PRO LOGIC
*11F
PRO LOGIC IIx MUSIC
*15P
PRO LOGIC IIx MOVIE
*15Q
PARTY
*134
NEO:6
13H
SOURCEDIRECT
13J
JAZZ-CLUB
*11K
HOLO TOGGLE
*11L
HOLO ON
*11M
HOLO OFF
*11N
MUTE TOGGLE
*11P
MUTE ON
*11Q
MUTE OFF
*11R
VOLUME UP
*11S
VOLUME DOWN
*11T
VOL ABSOLUTE
*11U + 2 EXT
*11U00 = zero vol
*11U99 = max vol
*11U00 = zero vol
*11U99 = max vol
ZONE2 PWR TOGGLE
*13M
ZONE2 PWR ON
*13N
ZONE2 PWR OFF
*13P
ZONE2 MUTE TGGLE
*13Q
ZONE2 MUTE ON
*13R
ZONE2 MUTE OFF
*13S
ZONE2 VOL UP
*13T
ZONE2 VOL DOWN
*13U
ZONE2 CD
*138
ZONE2 TAPE
*139
ZONE2 SAT
*13A
ZONE2 DVD
*13B
ZONE2 PHONO
*13C
ZONE2 TUNER
*13D
ZONE2 VID1
*13E
ZONE2 VCR
*13F
ZONE2 VID2
*13G
The TGIV has a rear panel
RS-232 Serial communication port.
This allows the FLASH memory to
be upgraded to the latest software by
connecting to a PC.
This allows the FLASH memory to
be upgraded to the latest software by
connecting to a PC.
The TGIV software may be updated
to refi ne operational details and to
include new features. Downloadable
updates will be posted on our website:
www.sunfi re.com.
include new features. Downloadable
updates will be posted on our website:
www.sunfi re.com.
Communications
Serial RS-232, 9600 Baud, 8-N-1
DB-9 Wiring
PINS 1, 6 and 4 are joined together
in ter nal ly
PINS 7 and 8 are joined together
in ter nal ly
PIN 2- Data from TGIV to controller
(TGIV transmit)
PIN 3- Data from controller to TGIV
(TGIV receive)
PIN 5- Ground/Common
PIN 9- No connection
The RS-232 connector is female.
Serial Cable
To connect the TGIV port to a
computer, you will need a "straight-
through" serial cable. This has con-
nector pins at one end connected
directly to the pins of the connector at
the other end. For example, pin 1 at
one end connects to pin 1 at the other
end, pin 2 connects to pin 2, pin 3 to
pin 3 and so on.
through" serial cable. This has con-
nector pins at one end connected
directly to the pins of the connector at
the other end. For example, pin 1 at
one end connects to pin 1 at the other
end, pin 2 connects to pin 2, pin 3 to
pin 3 and so on.
These common cables are avail-
able from most computer stores (or
from Radio Shack as # 26-117). It
should be 9-pin male at one end, to
fi t into the TGIV and normally 9-pin
female at the other, to fi t into your
computer's serial port (COM1 or
COM2).
from Radio Shack as # 26-117). It
should be 9-pin male at one end, to
fi t into the TGIV and normally 9-pin
female at the other, to fi t into your
computer's serial port (COM1 or
COM2).
External Control
The RS-232 port also allows the
TGIV to be controlled externally by
Home Theater controllers and com-
put ers.
Home Theater controllers and com-
put ers.
The following information is for
programmers and developers:
Partial Serial command set
Note that all stan dard com mands
and ex tend ed data are echoed back to
the sender. When a change is made
locally, the data is broad cast, except
for the case of “Toggle” and volume
commands. Here is a list of the most
popular commands. (Contact Sunfi re
Technical Support, or our website
www.sunfi re.com for a more extensive
list of commands).
the sender. When a change is made
locally, the data is broad cast, except
for the case of “Toggle” and volume
commands. Here is a list of the most
popular commands. (Contact Sunfi re
Technical Support, or our website
www.sunfi re.com for a more extensive
list of commands).
Update Procedure
1. The current version level of the
software running your TGIV
can be found by looking at the
Version Level OSD menu. This
is under the Software OSD
menu (see page 37).
can be found by looking at the
Version Level OSD menu. This
is under the Software OSD
menu (see page 37).
2. If the website fi le is newer than
your current version, follow the
website directions and down-
load the new fi le onto your
computer's hard drive.
website directions and down-
load the new fi le onto your
computer's hard drive.
3. Record your calibration, preset
stations or other settings on
page 57. In most cases, the
upgrade will not affect any of
these settings, but it is good to
record them just in case.
page 57. In most cases, the
upgrade will not affect any of
these settings, but it is good to
record them just in case.
4. Turn off your computer and
the TGIV. Position them close
enough so that they can be
easily connected using your
serial cable. If you have a lap-
top computer, then it may be
easier to bring that close to the
TGIV. Otherwise, you need to
disconnect the TGIV and move
it close to your computer.
enough so that they can be
easily connected using your
serial cable. If you have a lap-
top computer, then it may be
easier to bring that close to the
TGIV. Otherwise, you need to
disconnect the TGIV and move
it close to your computer.
5. Connect the TGIV RS-232 port
to the corresponding serial port
on your computer.
on your computer.
6. Turn on the TGIV and your
computer.
7. Find the fi le you downloaded in
step 2, and run the program.
8. In AUTO mode, the software
will look for an active serial
connection and upload the new
fi le. The TGIV display will show
the status.
connection and upload the new
fi le. The TGIV display will show
the status.
9. When the fi le transfer is com-
plete, press the Power switch
on the TGIV front panel. This
completes the upgrade.
on the TGIV front panel. This
completes the upgrade.
10. Turn off your computer and the
TGIV, and disconnect the serial
cable.
cable.