Sunfire IV User Manual
User's Manual
8
MAIN MENU
TRIMS
MODES
TONE
INPUTS
SETTINGS
MODES
TONE
INPUTS
SETTINGS
GUIDE
MENU
MODE
MODE
EXIT
INFO
SYSTEM
+10
POWER
3
1
6
4
9
7
ENT
DIS
M3
M1
2
5
8
0
M2
PAGE
FAV
MAIN
OFF
VOL
CH
MUTE
PREV
CH
CD
AUDIO
MAIN
TAPE
AUX
ZONE2
TGIV
DVD
VCR
SAT
TV
CABLE
MENU
Previous
MODE
TGIV
Next
MODE
MAIN
EXIT
CHAPTER 1
Quick Start Guide
13. The TGIV now needs to be setup
correctly to suit your speakers and
system. The following On Screen
Display (OSD) menus are used to
enter and make three main adjust-
ments:
system. The following On Screen
Display (OSD) menus are used to
enter and make three main adjust-
ments:
• Speaker Size
• Speaker Calibration
• Speaker Position
This setup needs to be done when
you use your system for the fi rst
time, or if you change anything
such as the amplifi ers or speak-
ers, or the speaker position. The
calibration is also a good way to
check that your system is working
correctly. These adjustments are
made using the OSD as follows:
time, or if you change anything
such as the amplifi ers or speak-
ers, or the speaker position. The
calibration is also a good way to
check that your system is working
correctly. These adjustments are
made using the OSD as follows:
13.1 Press MENU on the remote to
bring up the MAIN Menu of the
OSD on your TV.
OSD on your TV.
13.2 Use the joystick
pad left, right, up
and down buttons to
navigate through the
menus in the next
steps.
and down buttons to
navigate through the
menus in the next
steps.
NOTE: you can quit the OSD at
any time by pressing EXIT on the
remote. Any changes you make
will be saved. There is no need to
navigate back through previous
pages, unless you want to make
more changes.
remote. Any changes you make
will be saved. There is no need to
navigate back through previous
pages, unless you want to make
more changes.
When the OSD is active, the TGIV
front panel display shows an ab-
breviated message of where you
currently are in the menus.
breviated message of where you
currently are in the menus.
8. Press the remote MAIN button
a few times to make sure you
are on the Main Menu in the
remote's display.
are on the Main Menu in the
remote's display.
9. Set the remote to operate the
TGIV by pressing the TGIV
button.
button.
We hope that the following details
will help you get started using your
Theater Grand IV.
Theater Grand IV.
1. Take care to read and follow the
safety instructions on pages 2-3.
Also make sure that you read the
notes and details throughout the
manual, especially notes marked
with a warning triangle (
Also make sure that you read the
notes and details throughout the
manual, especially notes marked
with a warning triangle (
).
2. Add batteries to the remote control.
3. Connect your source equipment
and amplifi ers to the TGIV. See the
hookup diagrams on pages 15-24.
hookup diagrams on pages 15-24.
Make sure that all of your equip-
ment remains unplugged from
the AC mains until you have
made all the connections.
ment remains unplugged from
the AC mains until you have
made all the connections.
4. Connect the speakers to your am-
plifi ers.
5. In your DVD player's Audio setup
menu, set the digital output to
BITSTREAM. If this is not set cor-
rectly, the TGIV cannot decode the
digital information for 5.1 surround
sound playback.
BITSTREAM. If this is not set cor-
rectly, the TGIV cannot decode the
digital information for 5.1 surround
sound playback.
6. The TGIV has a bass management
system which allows the bass from
each speaker to be redirected to
a subwoofer. Larger speakers can
play the full frequency range, and
smaller speakers such as satellite
types can have their bass redirect-
ed. See page 42 for more details.
each speaker to be redirected to
a subwoofer. Larger speakers can
play the full frequency range, and
smaller speakers such as satellite
types can have their bass redirect-
ed. See page 42 for more details.
Make a note of which speak-
ers you would like to play the full
frequency range (Large) and those
which will have the bass redirected
(Small). Also make a note of the
approximate distance of each
speaker from your listening posi-
tion.
frequency range (Large) and those
which will have the bass redirected
(Small). Also make a note of the
approximate distance of each
speaker from your listening posi-
tion.
7. Turn on the TGIV, and then turn
on your amplifi ers, TV and other
source equipment.
source equipment.
10. Turn down the TGIV volume and
use the remote or front panel input
selector to select a video source.
selector to select a video source.
11. Play the source, and bring up the
volume to suit your taste. Make
sure the video can be seen in the
TV monitor.
sure the video can be seen in the
TV monitor.
12. Stop or pause the source.