Sony SRS-RF90R Manual

Page of 2
SONY SRS-RF90RK/RF90R (US,FR,ES) 3-236-404-
14
 (1)
SONY SRS-RF90RK/RF90R (US,FR,ES) 3-236-404-
14 
(1)
Disposing of the
speaker system
Be sure to remove the built-in rechargeable
batteries from the speaker system before you
dispose of the speaker system.
1
Remove 13 screws from the speaker
system using a cross-point screw driver
as illustrated below.
2
Open the cabinet of the speaker system
and remove the one screw to remove the
rechargeable battery as illustrated.
N
 Additional information
Precautions
• When the transmitter is not to be used for a long
period of time, disconnect the AC power
adaptor from the AC outlet holding the plug. Do
not pull on the cord.
Notes on the location you set the speaker
system
• Do not leave the wireless speaker system in a
location subject to:
– Direct sunlight or extremely high temperature such
as near a heater or in a car with its windows closed.
– High humidity such as in a bathroom.
– Excessive dust or sandy places.
– The speaker system is magnetically shielded, but do
not put a recorded tape, watch, cash card or floppy
disk in front of the speaker system.
• Set up the speaker system on a flat surface.
• Depending on where you set the speaker
system, it may fall down. Do not leave valuables
near the speaker system.
Notes on charging the battery
• When you charge the rechargeable battery, use
the supplied AC adaptor only.
• The charging time differs depending on usage
conditions of the battery.
• When you use the battery for the first time or the
battery is not to be used for a long time, the
battery duration time may become shorter than
the usual duration time. However, after you
charge the battery several times, the battery
duration time returns to its normal condition.
• If the battery duration time becomes half of its
normal time even after the battery is charged
fully, the battery is worn out. In this case,
consult your nearest Sony dealer.
Notes on using the speaker system
• Do not disassemble the speaker unit, built-in
amplifier or cabinet.
• Do not insert an object into the jack. Doing so
may cause a malfunction.
• Keep the volume at a moderate level to prevent
distortion.
• Do not carry the speaker unit by its reflector. If
you do so, the speaker system may detach from
the reflector.
Note on cleaning
Clean the cabinet of the speaker system with a soft
cloth slightly moistened with water or a mild
detergent solution. Do not use any type of abrasive
pad, scouring powder or solvent such as alcohol or
benzene as it may mar the finish of the cabinet.
When the color of your monitor screen
becomes irregular
Because this speaker system is magnetically
shielded, you can set it up near a monitor. But
depending on the model of the monitor, color
irregularity may occur.
To correct the color irregular
Turn off the monitor, and then turn it on again
after 15 to 30 minutes.
If color irregularity remains after
performing the above
• Separate the monitor and the speaker system.
• Make sure that no magnetic object, such as may
be attached to a door of shelf, healthcare device
or toys, etc., is located near the speaker system.
If you have any questions or problems concerning
the system that are not covered in this manual,
please consult your nearest Sony dealer.
Be sure to bring the speaker system and the
transmitter to the Sony dealer when requiring
repair work.
Troubleshooting
No sound/Muffled sound
, Check the connection of the audio/video
equipment.
, Check that the audio/video equipment is turned
on.
, Turn up the volume on the connected audio/
video equipment, if the transmitter is connected
to the headphones jack.
, Change the radio frequency with the CHANNEL
selector on the transmitter, then press the
TUNING button again.
, The speaker system’s POWER indicator light is
weak or turned off.
• Charge the built-in rechargeable battery or if the
POWER indicator is still off after charging the
built-in rechargeable battery, take the speaker
system to a Sony dealer for replacement of the
rechargeable battery.
, If you connect the transmitter to the LINE OUT or
REC OUT jack of an audio reproducer, make sure
that the NOISE FILTER switch is set to OFF.
, Make sure that the NOISE FILTER switch is set to
either ON or OFF (If the switch gets stuck
between ON and OFF, the sound will be cut off).
Distortion
, If the transmitter is connected to the headphones
jack, turn down the volume of the connected
audio/video equipment. If the connected audio/
video equipment has bass boost function, set its
function to OFF.
, If the connected audio/video equipment has a
LINE OUT jack, connect its LINE OUT jack.
, Change the radio frequency with the CHANNEL
selector on the transmitter.
, The speaker system’s POWER indicator light is
weak or turned off.
• Charge the built-in rechargeable battery or if the
POWER indicator is still off after charging the
built-in rechargeable battery, take the speaker
system to a Sony dealer for replacement of the
rechargeable battery.
, If you connect the transmitter to LINE OUT or
REC OUT jack of an audio reproducer, make sure
that the NOISE FILTER switch is set to OFF.
Loud background noise
, Move closer to the transmitter. As you move
away from the transmitter, more noise is likely to
be heard.
, If the transmitter is connected to the headphones
jack, turn up the volume of the connected audio/
video equipment.
, Change the radio frequency with the CHANNEL
selector on the transmitter, then press the
TUNING button again.
, The speaker system’s POWER indicator light is
weak or turned off.
• Charge the built-in rechargeable battery or if the
POWER indicator is still off after charging the
built-in rechargeable battery, take the speaker
system to a Sony dealer for replacement of the
rechargeable battery.
, If you connect the transmitter to the LINE OUT or
REC OUT jack of an audio reproducer, make sure
that the NOISE FILTER switch is set to OFF.
The battery duration time is short
, If you use the battery under the temperature
lower than 0 ˚C (32 ˚F), this is not a malfunction.
, The battery life may end. If the battery duration
time becomes half of its normal time even after
the battery is charged fully, consult your nearest
Sony dealer
Specifications
General
Carrier frequency 913.5 – 914.5 MHz
Channel
Ch1, Ch2, Ch3
Modulation
FM stereo
Transmitter (SRS-RF90RK only)
Power source
DC 9 V: supplied AC power adaptor
(AC-S901)
Audio input
phono jacks/stereo mini jack
Input impedance 33 k
Ω
/51 
Ω
 switchable
Dimensions
Approx. 136 
×
 100 
×
 136 mm
(6 
×
 4 
1
/
3
 
×
 6 in.) (w/h/d)
Mass
Approx. 146 g (5.2 oz.)
Speaker system  SRS-RF90RK, SRS-RF90R
Speaker system 2 way magnetically shielded
Enclosure type Bass reflex
Speaker units
tweeter: 30 mm 
×
 2
woofer: 57 mm 
×
 1
Power source
DC 9 V: supplied AC adaptor (AC-S906T)
Rated output
Built in amplifiers total 4W (while
using the supplied AC adaptor)
* power output:
Tweeter: 0.25W + 0.25W < 10%
T.H.D., 5 kHz 24 ohms
Woofer: 3.5W < 10% T.H.D., 1kHz
6 ohms
Dimensions
Approx. 234 
×
 300 
×
 126 mm
( 9 
1
/
4
 
×
  11 
7
/
8
 
×
 5 in.) (w/h/d)
Mass
Approx. 905 g (31.9 oz.) incl.
built-in rechargeable battery
Built-in Ni-MH rechargeable battery
Voltage
7.2 V
Capacity
700 mAh
Duration time
Approx. 4 hours
(with the 10 mW reflector light OFF)
Charging time
Approx. 28 hours (from fully
discharged to fully charged)
Supplied accessory
The transmitter (SRS-RF90RK only)
AC adaptor (2 for SRS-RF90RK) (1 for SRS-RF90R)
Connecting cord phono plug-stereo miniplug (1m) (1)
(SRS-RF90RK only)
Operating instructions (1)
Optional accessory
Plug adaptor
PC-236MS (stereo mini jack 
y
monaural mini plug)
Design and specifications are subject to change without notice.
Hooking up the system
Attaching the supplied reflector to
the speaker system
Insert the plugs until its base is settled firmly as
illustrated.
Connecting the transmitter to audio/
video equipment
For customers buying the SRS-RF90R
You can use the transmitter supplied with the
MDR-RF915RK or MDR-RF945RK. If you have
already set the transmitter, the following hookup
of the transmitter is not required. However, you
cannot use a transmitter supplied with a cordless/
wireless headphone system other than the above
models.
For customers buying the SRS-RF90RK
Set the transmitter by the following steps. Select
the hookup depending on the jack type of the
audio/video equipment you want to connect the
transmitter to.
A
To connect to a LINE OUT or REC OUT
B
To connect to headphones jack
2
The CHARGE indicator on the speaker
system will light up to indicate that the
battery is being charged.
Notes
• It takes about 28 hours to fully charge an empty battery.
• Charge the rechargeable battery within a temperature of
0 ˚C to 35 ˚C (32 ˚F to 95 ˚F).
• If you turn on the speaker system while charging the
battery, battery charging stops and the CHARGE
indicator turns off. You can use the speaker system by
the power from the AC adaptor.
• The duration time of the rechargeable battery is about 4
hours. If the light of the reflector becomes weak, it
means the rechargeable battery is low. So, turn off the
speaker system and charge the battery.
• Even after battery charging is finished, the CHARGE
indicator always lights up.
• The life of the built-in rechargeable battery is about 3
years. But it differs depending on operating conditions.
• Use only the supplied AC power adaptor. Do not use
any other AC power adaptor.
N
 Operating the system
Listening to a program
Before using the speaker system, charge the built-
in rechargeable battery first.
Turn down the volume of the speaker system
before playing back a program on the connected
audio/video equipment.
1
First turn on the audio/video equipment
and start playing.
The power indicator of the transmitter
will light up.
2
Turn on the speaker system.
The power indicator of the speaker
system will light in red.
3
Select the radio frequency with the
CHANNEL selector.
Note
If you use the unit near a cordless telephone, it may
cause radio interference. If poor reception occurs, try
another channel using the CHANNEL selector.
4
Turn up the volume to a moderate level
with the VOL control.
Press the TUNING button briefly for
automatic tuning of the speaker system.
If you do not receive a clear audio signal,
press it again.
Sending RF signals from the Transmitter
The transmitter starts sending the RF signals
automatically, when it detects audio signals from
the equipment connected.
If it does not detect an audio signal for more than
approximately four minutes, the transmitter will
stop sending RF signals, and the power indicator
turns off.
When the transmitter receives an audio signal
again, it starts sending the RF signals, and the
power indicator will light in red again.
If the audio signal is very weak, the transmitter
does not send RF signals. If the transmitter is
connected to a headphone jack, make sure the
volume of the equipment connected is set to 5 – 6
or higher.
You may not hear the beginning of the sound from
the speaker system until the transmitter starts
sending the RF signals after detecting an audio
signal.
Note
If the transmitter is connected to the headphones jack of
the source equipment, set the volume of that equipment as
high as possible without distorting the audio signal.
Using the Built-in Rechargeable Batteries
The built-in rechargeable batteries allow you to use
the unit anywhere.
Remove the supplied AC power adaptor from the
DC IN jack of the unit to use the built-in
rechargeable batteries.
To use the illumination of the reflector
Turn on the switch of the reflector light.
Notes
• If a hissing noise is heard, move it closer to the
transmitter.
• If you turn up the volume of the speaker system too
high, the light of the reflector may flicker. But this is not
a malfunction.
• If you hold the antenna of the transmitter with your
hand, noise may occur. But this is not a malfunction.
Operating Instructions
Mode d’emploi
Manual de instrucciones
Wireless Stereo
Speaker System
© 2002 Sony Corporation    
Printed in Korea
SRS-RF90RK
SRS-RF90R
3-236-404-14(1)
English
1 2 3
CHANNEL
Owner’s Record
The model number is located at the bottom of the transmitter and the speaker
system.
The serial number is located at the bottom of the transmitter and the speaker
system.
Record these numbers in the spaces provided below. Refer to them whenever
you call upon your Sony dealer regarding this product.
 Model No. 
 Transmitter 
 Speaker system 
Serial No.
Transmitter 
 Speaker system 
WARNING
To prevent fire or shock hazard, do not expose
the unit to rain or moisture.
To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified personnel
only.
Information
You are cautioned that any changes or modifications
not expressly approved in this manual could void
your authority to operate this equipment.
For the Customers in the U.S.A.
If you have any questions about this product, you
may call;
Sony Customer Informaion Services Center
1-800-222-7669 or http://www.sony.com/
Declaration of Conformity
Trade Name:
SONY
Model No.:
SRS-RF90R
(Speaker Unit)
Responsible Party: Sony Electronics Inc.
Address:
16450  W. Bernardo Dr,
San Diego, CA 92127 USA
Telephone No.:
858-942-2230
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired operation.
Welcome!
Thank you for purchasing the Sony
SRS-RF90RK/RF90R Wireless Stereo Speaker
System. Before operating the unit, please read this
manual thoroughly and retain it for future reference.
Some features are:
• Wireless system that allows you to use your
system free from the restriction of speaker cords.
• Wide signal reception range up to about 150 feet
(46 m).
• 3 Channel options on transmitter for optimum
signal reception.
• Auto tuning function available on speaker.
• Reflector attached on the speaker system creates
a high fidelity sound field.
• The one-box stereo type structure produces a
wide soundstage.
• This speaker system can be powered two ways;
you can use the supplied AC power adaptor or
built-in rechargeable battery.
• Novel and unconventional design with blue-
illumination for an attractive showpiece in any
room.
Notes on receiving
performance
The system for this equipment utilizes very high
frequency signals in the 900 MHz band so the
receiving performance may deteriorate due to the
surroundings. The following examples illustrate
conditions that may reduce the possible receiving
range or cause interference with reception.
• Inside a building with walls containing steel
beams.
• Area with many steel file cabinets, etc.
• Area with many electrical appliances capable of
generating electromagnetic noise.
• Transmitter is placed on a metal instrument.
• Area facing roadways.
• Noise or interfering signals exist in the
surroundings due to radio transceivers in trucks,
etc.
• Noise or interfering signals exist in the
surroundings due to wireless communication
systems installed along roadways.
• Transmitter is placed directly on floor.
Placing it up off the floor, such as on a desk, is
recommended.
DC IN 9V
OFF
ON
FILTER
NOISE
1 2 3
CHANNEL
R
B
A
L
AUDIO IN
Transmitter
to AUDIO IN
B jack
Connecting cord
(supplied)
Right channel
(red)
Left channel
(white)
to LINE OUT or REC
OUT jacks
Stereo system, VCR, etc.
CHARGE indicator
Battery
For the Customers in Canada
Operation is subject to the following two
conditions: (1) this device may not cause
interference, and (2) this device must accept any
interference, including interference that may cause
undesired operation of the device.
DC IN 9V
OFF
ON
FILTER
NOISE
1 2 3
CHANNEL
R
B
A
L
AUDIO IN
Transmitter
Left channel
(white)
Right channel
(red)
Connecting cord
(supplied)
to AUDIO IN
A jacks
Unimatch plug
adaptor (not
supplied)
Discman, MD,
WALKMAN*, VCR,
etc.
to headphones
or LINE OUT jack
(stereo mini jack)
to headphones
jack (stereo
phone jack)
For the customers in the USA and Canada
RECYCLING NICKEL METAL HYDRIDE
BATTERIES
Nickel Metal Hydride
batteries are recyclable.
You can help preserve our
environment by returning
your used rechargeable
batteries to the collection and
recycling location nearest you.
For more information regarding recycling of
rechargeable batteries, call toll free
1-800-822-8837, or visit http://www.rbrc.org/
Caution: Do not handle damaged or leaking
Nickel Metal Hydride batteries.
N
 Getting started
Unpacking
Check that you have the following items:
• The speaker system
• The transmitter (SRS-RF90RK only)
• AC power adaptor
(2 for SRS-RF90RK) (1 for SRS-RF90R)
• Connecting cord (phono plugs 
y stereo mini
plug), 1 m (SRS-RF90RK only)
C
To connect to TV, etc.
If noise occurs when the transmitter is
connected to the headphone jack of your
TV or VCR, set the NOISE FILTER switch
to ON.
Notes
• If you connect the transmitter to LINE OUT or REC
OUT jack, do not set the NOISE FILTER switch to
ON. Otherwise, the volume will be limited.
• The NOISE FILTER switch effects the sound only in
case of such as connection diagram C. In diagrams
A
 and B, the switch has no effect.
• When the transmitter is placed on or near a TV, it
may pick up a noise. In such case, place the
transmitter away from the TV.
Connecting the transmitter to an AC
outlet using the supplied AC power
adaptor
Notes
• Use only the supplied AC power adaptor. Do not use
any other AC power adaptor.
Polarity of the plug
• When you connect the connecting cord directly to an
earphone jack, the audio signal will not be output
through the right channel. In such a case, use the
separately sold PC-236MS plug adaptor.
• If the connected equipment has the AVLS (Automatic
Volume Limiter System) function, be sure to turn the
function off when using the transmitter. Otherwise, you
will have to turn up the volume of the speaker system,
and that may cause noise.
• If the connected equipment has the BASS BOOST or
MEGA BASS function, be sure to turn the function off
when using the transmitter. Otherwise, the sound from
the speaker system may be distorted.
• Do not place the transmitter near a fluorescent lamp, etc.
when using the system.
* “WALKMAN” is a registered trademark of Sony
Corporation to represent Headphone Stereo products.
The effective areas of the
transmitter
The optimum distance is up to approximately 150
feet (46 m) without the system picking up some
interference. However, the distance may vary
according to the surroundings and environment. If
the system picks up some noise while using it
within the above mentioned distance, reduce the
distance between the transmitter unit and the
speaker system, or select another channel.
Notes
• When you use the speaker system inside the effective
areas of the transmitter, the transmitter can be placed in
any direction from the listener.
• Even within the signal reception area, there are some
spots (dead spot) where the RF signal cannot be
received. This is a characteristic inherent to RF signals,
and does not indicate malfunction. By slightly moving
the transmitter, location of the dead spot can be
changed.
Charging the speaker
system battery
Using the speaker system for the first
time
When you use the system for the first time, charge
the battery in the following manner.
1
Connect the speaker system to a power
source.
to an AC outlet
To DC IN
9 V jack
AC power adaptor
(supplied: AC-S901)
Transmitter
DC IN 9V
OFF
ON
FILTER
NOISE
1 2 3
CHANNEL
R
B
A
L
AUDIO IN
TV, etc.
to stereo mini jack
Transmitter
to AUDIO IN
A jack
Left channel
(white)
Right channel
(red)
Connecting cord
(supplied)
AC power adaptor (supplied)
Tweeter
(left)
Tweeter
(right)
To an AC
outlet
OFF y ON
The switch of the
reflector light
POWER switch
POWER indicator
High
Low
TUNING
button
VOLUME control
Raccordement du
système
Raccordement du réflecteur fourni au
système d’enceinte
Insérez les fiches solidement et jusqu’au fond, tel
qu’illustré.
Raccordement du transmetteur à un
appareil audio ou vidéo
Pour les propriétaires du SRS-RF90R
Vous pouvez utiliser le transmetteur fourni soit
avec le MDR-RF915RK, soit avec le MDR-
RF945RK. Si vous avez déjà installé le
transmetteur, il n’est pas nécessaire d’effectuer le
raccordement suivant. Cependant, vous ne pouvez
pas utiliser un transmetteur fourni avec un
système de casque d’écoute sans fil d’un modèle
autre que ceux cités ci-dessus.
Pour les propriétaires du SRS-RF90RK
Installez le transmetteur en effectuant les étapes
suivantes. Choisissez le raccordement à effectuer
selon le type de prise de l’appareil audio ou vidéo
auquel vous souhaitez raccorder le transmetteur.
A
Raccordement à une prise LINE OUT ou
REC OUT
B
Raccordement à une prise de casque
Bienvenue !
Nous vous remercions d’avoir fait l’acquisition du
système d’enceinte stéréo sans fil SRS-RF90RK/
RF90R de Sony. Avant de faire fonctionner cet
appareil, lisez attentivement le présent mode
d’emploi et conservez-le pour toute référence
ultérieure.
Cet appareil offre, entre autres, les caractéristiques
suivantes :
• Système sans fil vous permettant l’utilisation
sans fils d’enceinte encombrants.
• Longue portée de transmission des signaux allant
jusqu’à environ 46 m (150 pi).
• Trois options de canaux de transmission
permettant une réception optimale des signaux.
• Fonction de syntonisation automatique à
l’enceinte.
• Réflecteur fixé au système d’enceinte offrant une
reproduction sonore haute fidélité.
• Construction stéréo à boîtier unique offrant un
large champ sonore.
• Deux possibilités d’alimentation : avec
l’adaptateur CA fourni ou la batterie
rechargeable intégrée.
• Conception novatrice et originale avec éclairage
bleu, un design élégant qui convient bien au
décor de n’importe quelle pièce.
Remarques sur la
qualité de
transmission
Comme le système de cet appareil utilise des
signaux de très haute fréquence dans la bande des
900 MHz, l’environnement de l’appareil peut
entraîner une détérioration de la qualité de
transmission. Les exemples suivants illustrent les
situations pouvant réduire la plage de
transmission et perturber la réception.
• Utilisation à l’intérieur d’un bâtiment à structure
en acier.
• Utilisation dans des pièces contenant de
nombreux classeurs ou autres éléments en acier.
• Utilisation à proximité d’un grand nombre
d’appareils électriques générant des parasites
électromagnétiques.
• Installation du transmetteur sur un instrument
métallique.
• Utilisation à proximité d’une route.
• Parasites ou interférences autour de l’appareil,
provenant d’émetteurs-récepteurs de camions
ou d’autres appareils.
• Parasites ou interférences autour de l’appareil,
provenant de systèmes de communication sans
fil installés le long des routes.
• Installation du transmetteur directement sur le
sol. Il est recommandé d’installer le
transmetteur en hauteur, par exemple sur un
bureau.
AVERTISSEMENT
Pour éviter tout risque d’incendie ou
d’électrocution, ne pas exposer cet appareil à la
pluie ou à l’humidité.
Pour prévenir tout risque d’électrocution,
n’ouvrez jamais le coffret. Adressez-vous à un
personnel qualifié uniquement pour toute
intervention sur l’appareil.
Avertissement
Soyez avisé que toute modification non
expressément approuvée dans le présent mode
d’emploi pourrait entraîner l’annulation de vos
droits d’utilisation de ce produit.
Pour les utilisateurs au Canada
Son utilisation est autorisée seulement aux
conditions suivantes: (1) il ne doit pas produire de
brouillage et (2) l’utilisateur du dispositif doit être
prêt à accepter tout brouillage radioeléctrique reçu,
même si ce brouillage est susceptible de
compromettre le fonctionnement du dispositif.
Français
N
 Préparatifs
Déballage
Vérifiez que vous disposez de tous les éléments
suivants :
• Système d’enceinte
• Transmetteur (SRS-RF90RK uniquement)
• Adaptateur CA
(deux pour le SRS-RF90RK) ou (un pour le
SRS-RF90R)
• Câble de liaison (prises phono 
y mini-fiche
stéréo), 1 m (SRS-RF90RK uniquement)
Vers une prise
CA
Vers la
prise
DC IN 9 V
Adaptateur CA
(fourni : AC-S901 )
Transmetteur
Adaptateur CA (fourni)
Haut-parleur des
aiguës (gauche)
Haut-parleur
des aiguës
(droit)
Vers une prise CA
Pour les utilisateurs aux Etats-Unis et au Canada
RECYCLAGE DES ACCUMULATEURS À
HYDRURE MÉTALLIQUE DE NICKEL
Les accumulateurs à hydrure
métallique de nickel sont
recyclables.
Vous pouvez contribuer à
préserver l’environnement en
rapportant les piles usées dans
un point de collection et
recyclage le plus proche.
Pour plus d’informations sur le recyclage des
accumulateurs, téléphonez le numéro gratuit
1-800-822-8837 (Etats-Unis et Canada
uniquement), ou visitez
http://www.rbrc.org/
Avertissment : Ne pas utilliser des
accumulateurs à hydrure métallique de nickel
qui sont endommagées ou qui fuient.
Voir page suivante
DC IN 9V
OFF
ON
FILTER
NOISE
1 2 3
CHANNEL
R
B
A
L
AUDIO IN
Transmetteur
Vers la prise
AUDIO IN B
Câble de liaison
(fourni)
Canal droit
(rouge)
Canal gauche
(blanc)
Vers les prises LINE
OUT ou REC OUT
Chaîne stéréo,
magnétoscope, etc.
DC IN 9V
OFF
ON
FILTER
NOISE
1 2 3
CHANNEL
R
B
A
L
AUDIO IN
Transmetteur
Canal gauche
(blanc)
Canal droit
(rouge)
Câble de liaison
(fourni)
Vers les prises
AUDIO IN A
Adaptateur de
fiche universel
(non fourni)
Discman, MD,
WALKMAN*,
magnétoscope, etc.
Vers la prise de
casque ou LINE OUT
(mini-prise stéréo)
Vers la prise de
casque (prise
stéréo)
DC IN 9V
OFF
ON
FILTER
NOISE
1 2 3
CHANNEL
R
B
A
L
AUDIO IN
Téléviseur ou
autre appareil
Vers la mini-prise
stéréo
Transmetteur
Vers les prises
AUDIO IN A
Canal gauche
(blanc)
Canal droit
(rouge)
Câble de liaison
(fourni)
C
Raccordement à un téléviseur ou à un
autre appareil.
Si des parasites sont audibles lorsque le
transmetteur est relié à la prise de casque
de votre téléviseur ou magnétoscope,
réglez le commutateur NOISE FILTER à
ON.
Remarques
• Si vous raccordez le transmetteur à une prise LINE
OUT ou REC OUT, ne réglez pas le commutateur
NOISE FILTER à ON, sinon le volume sera limité.
• Le commutateur NOISE FILTER n’agit sur le son
que dans les cas ou le raccordement du schéma C
est utilisé. Dans les cas où le raccordement A ou B
est utilisé, il n’a aucun effet.
• Placé près d’un téléviseur, le transmetteur risque de
subir des interférences. Le cas échéant, éloignez-le
du téléviseur.
Raccordement du transmetteur à une
prise de courant à l’aide de
l’adaptateur CA fourni.
Remarques
• Utilisez uniquement l’adaptateur CA fourni. N’utilisez
aucun autre adaptateur CA.
Polarité de la fiche
• Lorsque vous raccordez directement le câble de liaison à
une prise de casque, le signal audio n’est pas émis par le
canal droit. Dans ce cas, utilisez l’adaptateur de fiche
PC-236MS vendu séparément.
• Si l’appareil raccordé est équipé de la fonction AVLS
(système de limitation automatique du volume),
désactivez cette fonction lorsque vous utilisez le
transmetteur. Sinon, vous devrez augmenter le volume
du système d’enceinte, ce qui pourrait engendrer des
parasites.
• Si l’appareil raccordé est équipé de la fonction BASS
BOOST ou MEGA BASS (amplification des graves,
désactivez cette fonction lorsque vous utilisez le
transmetteur. Sinon, le son provenant du système
d’enceinte risque d’être déformé.
• N’installez pas le transmetteur près d’une lampe
fluorescente, etc. lorsque vous utilisez le système.
* «WALKMAN» est une marque déposée par Sony
Corporation pour représenter les produits stéréo dotés
d’écouteurs.
Portée du transmetteur
La portée optimale du transmetteur est de 46 m
(150 pi) environ sans que le système ne capte
d’interférences. Cependant, cette distance peut
varier selon l’environnement de l’appareil. Si le
système capte des parasites alors qu’il est utilisé
dans la zone définie ci-dessus, rapprochez le
transmetteur et le système d’enceinte ou
sélectionnez un autre canal.
Remarques
• Quand vous utilisez le système d’enceinte dans la zone
de couverture du transmetteur, la direction du
transmetteur par rapport à l’auditeur n’importe pas.
• Dans la zone de réception des signaux, il existe
cependant certains endroits (zones de silence) où la
réception des signaux RF est impossible. Il s’agit d’une
caractéristique inhérente aux signaux RF et n’indique
pas un problème de fonctionnement. Il est possible de
modifier l’emplacement de la zone de silence en
déplaçant légèrement le transmetteur.
Recharge de la batterie
du système d’enceinte
Première utilisation du système
d’enceinte
Lorsque vous utilisez le système pour la première
fois, chargez la batterie tel qu’indiqué ci-dessous.
1
Raccordez le système d’enceinte à une
source d’alimentation.