Sharp 10P02-MA-NM User Manual
83
Appendix
The following messages appear on the TV screen in case of an error during operation.
Error message
Possible Error
Suggested Solution
Cannot play.
The disc cannot be played back with
this system.
this system.
•
Check the disc, and load it correctly.
•
Incompatible disc.
If you load a disc which cannot be
played with this system (i.e. a scratched
disc), or if you load a disc upside down,
this message will appear, and the disc
tray will automatically pop out.
played with this system (i.e. a scratched
disc), or if you load a disc upside down,
this message will appear, and the disc
tray will automatically pop out.
•
Occurs if the loaded disc cannot be
played because it is a non-standard disc
or scratched, etc.
played because it is a non-standard disc
or scratched, etc.
•
Remove the disc.
•
Cannot operate.
Occurs if an operation is incorrect.
•
—
This USB memory is not formatted
properly. Please format the memory in
USB memory management.
properly. Please format the memory in
USB memory management.
Occurs if there is a formatting error.
Occurs if the USB memory is not
formatted with FAT 32/16.
Occurs if the USB memory is not
formatted with FAT 32/16.
•
•
•
Format the USB memory again.
Format the USB memory with your
PC.
Format the USB memory with your
PC.
•
•
•
The Connected USB Memory cannot
be used. It should be compliant with
USB 2.0
be used. It should be compliant with
USB 2.0
Occurs if USB memory not compliant
with USB 2.0 High Speed (480Mbit/s) is
used (i.e. USB 1.0/USB 1.1).
with USB 2.0 High Speed (480Mbit/s) is
used (i.e. USB 1.0/USB 1.1).
•
Connect USB 2.0 High Speed
(480Mbit/s) compliant USB memory.
(480Mbit/s) compliant USB memory.
•
The following messages are displayed on the main unit, when you fail to perform operations properly.
Error Message
Possible Error
Suggested Solution
The cooling fan at the rear of the main
unit does not run.
unit does not run.
•
Unplug the AC power cord and
check if foreign objects get caught
around the cooling fan. *
check if foreign objects get caught
around the cooling fan. *
•
STANDBY indicator (blinks red)
Is volume setting very high?
Is system placed in a very hot location?
Is system placed in a very hot location?
•
•
•
If the system is operated at very high
volume levels or in a hot location for
an extended period, the protection
circuitry may be triggered.
Unplug the AC power cord and plug
it in again after 5 minutes or more.
Then check the operation. *
volume levels or in a hot location for
an extended period, the protection
circuitry may be triggered.
Unplug the AC power cord and plug
it in again after 5 minutes or more.
Then check the operation. *
•
Should the same message appear even if the system is unplugged and plugged in or is set to the stand-by mode and on
again, contact your local dealer where you purchased the system
again, contact your local dealer where you purchased the system
To Reset this System
If this system receives strong interference from a source such as excessive static electricity,
strong external noise, malfunction of power supply, or voltage caused by lightning during
use or a wrong operation is sent to the system, errors like the system not accepting an
operation may occur.
Press and hold
strong external noise, malfunction of power supply, or voltage caused by lightning during
use or a wrong operation is sent to the system, errors like the system not accepting an
operation may occur.
Press and hold
POWER (for about 15 seconds) on the main unit.
If the power is on, keep the button pressed down until the front panel display turns off.
When the front panel display is turned off, the reset procedure is complete.
When the front panel display is turned off, the reset procedure is complete.
If the power is off, keep the button pressed down until the STANDBY indicator turns off.
When the STANDBY indicator is turned off, the reset procedure is complete.
When the STANDBY indicator is turned off, the reset procedure is complete.
Then, after the STANDBY indicator is lit, turn on the power.
When a reset is performed while the power is on, the system will turn off. Turn the power on again. At this point, it may take
a few moments for the system processing to finish before the system is ready for use. During the system processing, the
BD/DVD/CD mode indicator on the front panel display of the main unit will blink. Once the system processing has finished, the
indicator will finish blinking and then light up normally. You can operate the system when the BD/DVD/CD mode indicator is lit.
Since all settings including the language setting stored in memory are also reset when a reset has been performed, they must
be set again.
When the problem persists even after performing a reset, unplug the AC cord and plug it in again. If this does not solve the
problem, contact the nearest service center approved by SHARP.
When a reset is performed while the power is on, the system will turn off. Turn the power on again. At this point, it may take
a few moments for the system processing to finish before the system is ready for use. During the system processing, the
BD/DVD/CD mode indicator on the front panel display of the main unit will blink. Once the system processing has finished, the
indicator will finish blinking and then light up normally. You can operate the system when the BD/DVD/CD mode indicator is lit.
Since all settings including the language setting stored in memory are also reset when a reset has been performed, they must
be set again.
When the problem persists even after performing a reset, unplug the AC cord and plug it in again. If this does not solve the
problem, contact the nearest service center approved by SHARP.
*
•
•
•
•
•
•
•
POWER
STANDBY
indicator
indicator
Front panel
display
display
POWER
STANDBY
indicator
indicator
Front panel
display
display
Error Messages
BD-MPC41U_E.indb 83
BD-MPC41U_E.indb 83
2010/02/04 16:15:06
2010/02/04 16:15:06