Arcam C30 User Manual
10
10
11
E
n
g
li
sh
POWER INLET
OUT
VOLTAGE
SELECT
230V
GAIN
XLR/
PHONO
TRIG
OUT
REMOTE
IN
4 – 16 OHMS
–
+
SPEAKERS
–
+
AUDIO
IN
P1
ARCAM
XLR
PHONO
BALANCED AUDIO
OUT
IN
Installation: P35 and P1 power amplifiers
POSITIONING THE UNIT
Place your amplifier on a level, firm surface.
Avoid placing the unit in direct sunlight or near sources of heat or
damp.
Ensure adequate ventilation. Do not place the unit in an enclosed space
such as a bookcase or cabinet as both of these will impede air flow
through the unit, which is necessary for cooling.
Avoid placing the unit in direct sunlight or near sources of heat or
damp.
Ensure adequate ventilation. Do not place the unit in an enclosed space
such as a bookcase or cabinet as both of these will impede air flow
through the unit, which is necessary for cooling.
CONNECTING TO A POWER SUPPLY
MAINS LEAD
The appliance is normally supplied with a moulded mains plug already
fitted to the lead. If for any reason the plug needs to be removed, it
must be disposed of immediately and securely, as it is a potential shock
hazard when inserted into the mains socket. Should you require a new
mains lead, contact your Arcam dealer.
fitted to the lead. If for any reason the plug needs to be removed, it
must be disposed of immediately and securely, as it is a potential shock
hazard when inserted into the mains socket. Should you require a new
mains lead, contact your Arcam dealer.
WRONG PLUG?
Check that the plug supplied with the unit fits your supply and that your
mains supply voltage agrees with the voltage setting (115V or 230V)
indicated on the rear panel of the unit before plugging in.
If your mains supply voltage or mains plug is different, consult your
Arcam dealer.
This product must be earthed.
mains supply voltage agrees with the voltage setting (115V or 230V)
indicated on the rear panel of the unit before plugging in.
If your mains supply voltage or mains plug is different, consult your
Arcam dealer.
This product must be earthed.
PLUGGING IN
Push the plug (IEC line socket) of the power cable supplied with the
unit into the socket (POWER INLET) in the back of the unit. Make sure
it is pushed in firmly.
Put the plug on the other end of the cable into your power supply
socket and switch the socket on.
unit into the socket (POWER INLET) in the back of the unit. Make sure
it is pushed in firmly.
Put the plug on the other end of the cable into your power supply
socket and switch the socket on.
STAND-BY POWER
For remote stand-by operation, the amplifier’s control power supply is
kept powered up all the time the unit is connected to the mains supply.
The front panel power switch powers down all other circuitry. Power
consumption in this mode is less than 2W.
This means that even though the power switch is off, it may be possible
to hear a slight residual hum coming from the mains transformer inside
the amplifier. This is perfectly normal. If the unit is to be left unused for
an extended period, we recommend that it is disconnected from the
mains supply by switching it off at the wall socket
kept powered up all the time the unit is connected to the mains supply.
The front panel power switch powers down all other circuitry. Power
consumption in this mode is less than 2W.
This means that even though the power switch is off, it may be possible
to hear a slight residual hum coming from the mains transformer inside
the amplifier. This is perfectly normal. If the unit is to be left unused for
an extended period, we recommend that it is disconnected from the
mains supply by switching it off at the wall socket
IMPORTANT:
Ensure that the amplifier is switched off before attempting to
connect the speakers, and check carefully any connections made
before turning the unit back on.
Ensure that the amplifier is switched off before attempting to
connect the speakers, and check carefully any connections made
before turning the unit back on.
P35 POWER AMPLIFIER: REAR PANEL
P1 POWER AMPLIFIER: REAR PANEL
+
R/CH1
–
CTR/CH3
SP1
SP2
POWER INLET
OUT
IN
L
R
VOLTAGE
SELECT
230V
4 – 16 OHMS
+
L/CH2
–
+
R/CH1
–
+
L/CH2
–
AUDIO
SP1
SP2
4 – 16 OHMS
+
CTR/CH3
–
+
CTR/CH3
–
AUDIO
IN
OUT
LINK
REMOTE
IN
TRIG
OUT
Optional Third Channel
Module – provides a third
90W channel suitable for
Home Cinema or multi-
channel audio use.
Module – provides a third
90W channel suitable for
Home Cinema or multi-
channel audio use.