Arcam C30 User Manual
44
5
E
n
g
li
sh
POSITIONING THE UNIT
Place your amplifier on a level, firm surface.
Avoid placing the unit in direct sunlight or near sources of heat or
damp.
Ensure adequate ventilation. Do not place the unit in an enclosed space
such as a bookcase or cabinet as both of these will impede air flow
through the unit.
Avoid placing the unit in direct sunlight or near sources of heat or
damp.
Ensure adequate ventilation. Do not place the unit in an enclosed space
such as a bookcase or cabinet as both of these will impede air flow
through the unit.
CONNECTING TO A POWER SUPPLY
MAINS LEAD
The appliance is normally supplied with a moulded mains plug already
fitted to the lead. If for any reason the plug needs to be removed,
it must be disposed of immediately and securely, as it is a potential
shock hazard when inserted into the mains socket. Contact your
Arcam dealer if you need a new mains lead.
fitted to the lead. If for any reason the plug needs to be removed,
it must be disposed of immediately and securely, as it is a potential
shock hazard when inserted into the mains socket. Contact your
Arcam dealer if you need a new mains lead.
WRONG PLUG?
Before plugging in, check that the plug supplied with the unit fits your
supply and that your mains supply voltage agrees with the voltage
setting (115V or 230V) indicated on the rear panel of the unit
supply and that your mains supply voltage agrees with the voltage
setting (115V or 230V) indicated on the rear panel of the unit
2
.
If your mains supply voltage or mains plug is different, consult your
Arcam dealer.
This product must be earthed.
Arcam dealer.
This product must be earthed.
PLUGGING IN
Push the plug (IEC line socket) of the power cable supplied with the
unit into the socket (
unit into the socket (
POWER INLET
)
1
in the back of the unit. Make
sure it is pushed in firmly.
Put the plug on the other end of the cable into your power supply
socket and switch the socket on.
Put the plug on the other end of the cable into your power supply
socket and switch the socket on.
STAND-BY POWER
For remote stand-by operation, the amplifier’s control power supply is
kept powered up all the time the unit is connected to the mains supply.
The front panel power switch powers down all other circuitry. Power
consumption in this mode is less than 2W.
This means that even though the power switch is off, it may be possible
to hear a slight residual hum coming from the mains transformer inside
kept powered up all the time the unit is connected to the mains supply.
The front panel power switch powers down all other circuitry. Power
consumption in this mode is less than 2W.
This means that even though the power switch is off, it may be possible
to hear a slight residual hum coming from the mains transformer inside
Installation: C30 pre-amplifier
L
R
PHONO
POWER INLET
PRE OUT
BUFFERED
L
R
L
R
L
R
VOLTAGE
SELECT
RECORD
OUT
PLAY
IN
TAPE/PROC
RECORD
OUT
PLAY
IN
VCR/TAPE 2
DVD
AV
TUNER
CD
AUX
MM
MC
REMOTE
IN
TRIG
OUT
115/230V
DIRECT
the amplifier. This is perfectly normal. If the unit is to be left unused for
an extended period, we recommend that it is disconnected from the
mains supply by switching it off at the wall socket.
an extended period, we recommend that it is disconnected from the
mains supply by switching it off at the wall socket.
POWER AMPLIFIER CONNECTION
PRE OUT
456
– The recommended connection between
the C30 pre-amplifier and your power amplifier depends on both the
distance between the two and the type of power amplifier that you are
using. There are three options:
distance between the two and the type of power amplifier that you are
using. There are three options:
1. If the cables to be used to connect the C30 to the power
amplifier are less than 3m long, we recommend connecting the
DIRECT
sockets
6
to the input sockets of your power amplifier.
On the P35 and P1, connect to the socket(s) labelled
AUDIO IN
.
If the cables to be used to connect the C30 to the power amplifier
are 3m or longer, then the connection to use depends on the type of
power amplifier you have.
are 3m or longer, then the connection to use depends on the type of
power amplifier you have.
2. If your power amplifier does not have balanced inputs (such as
the P35), use the
BUFFERED
outputs
5
. On the P35, connect to
the sockets labelled
AUDIO IN
.
3. If your power amplifier provides balanced inputs (such as the P1),
use the balanced outputs
4
. On the P1, connect to the sockets
labelled
BALANCED AUDIO IN
.
The buffered and balanced outputs are designed to drive longer cables
than the direct output. Note that using the buffered outputs to drive
the P1 does not degrade the signal and will in no way damage either
piece of equipment.
than the direct output. Note that using the buffered outputs to drive
the P1 does not degrade the signal and will in no way damage either
piece of equipment.