Sony MZ-E45 User Manual
– 7 –
SECTION 4
TEST MODE
Outline
•
In this set, overall adjustment mode is made available by enter-
ing test mode to perform automatic adjustment of CD and MO.
In the overall adjustment mode, the disc is determined whether
it is CD or MO and adjustments are performed in sequence. If a
fault is found, the location of the fault is displayed. Also, in servo
mode, each adjustment can be automatically made.
ing test mode to perform automatic adjustment of CD and MO.
In the overall adjustment mode, the disc is determined whether
it is CD or MO and adjustments are performed in sequence. If a
fault is found, the location of the fault is displayed. Also, in servo
mode, each adjustment can be automatically made.
Setting the Test Mode
To enter the test mode, two methods are available :
1. Entering method with key input.
1. Entering method with key input.
Turn on the HOLD switch on the set. While holding down the
p
key on the set, press the following remote commander keys in
the following order :
+
the following order :
+
n +
n =
n =
n +
n =
n +
n
=
n P n P
2. Entering method by shorting the test point
Solder bridge the test point TAP801 (TEST) on the main board
(connect IC801 pin #™ to GND), and turn on the POWER.
(connect IC801 pin #™ to GND), and turn on the POWER.
[MAIN BOARD] (Conductor side)
Releasing the Test Mode
1. When test mode was entered with key input, turn off the POWER.
2. When test mode was entered by shorting the test point, turn off
2. When test mode was entered by shorting the test point, turn off
the POWER and open the solder bridge of TAP801 (TEST
MODE) on the main board.
MODE) on the main board.
Operation of Setting on Test Mode
When the test mode is set, the LCD displays the following :
•
The cycle - the above ROM version display
n
All lit
n
All off
- is repeated.
(The ROM version is constantly displayed.)
(The ROM version is constantly displayed.)
•
When the PLAY MODE key is pressed and hold down, the dis-
play at that time is held so that display can be checked.
play at that time is held so that display can be checked.
Configuration of Test Mode
The test mode has the configuration given below.
Servo Mode
•
Set the test mode, press the VOLUME – key and use the
” key
to set the servo mode.
•
When the servo mode is set, use the
+
key and the
=
key
to move the optical pick-up to the outer circumference and to
the inner circumference respectively.
the inner circumference respectively.
•
When entering another mode, refer to the configuration of test
mode.
mode.
1. Structure of Servo Mode
V 3 . 3 0 0
ROM version display
LCD on remote commander
”
key
”
key
p
key
p
key
p
key
p
key
VOL
+ key
+ key
VOL
– key
– key
(Start ?)
Overall
adjustment
mode (Auto?)
Adjustment
mode
(Manu ?)
Servo mode
0 0 0
Audio mode
1 0 0
Servo mode
3 0 0
+, – keys
+, – keys
+, – keys
Display when test mode is set
Displays of the LCD on the remote commander
are shown in parentheses.
are shown in parentheses.
Servo mode
0 0 0
Offset adjustment
0 1 0
Laser power
adjustment
0 2 0
011
to
013
*
1
021
to
024
*
1
2
3
1
p
key
p
key
p
key
p
key
”
key
”
key
”
key
”
key
”
key
+, – keys
+, – keys
(See page 8)
*
1 Repeatedly press
”
key
to change the mode.
(Refer to the following list
for a description of each
mode.)
(Refer to the following list
for a description of each
mode.)
Test mode
Short : Test mode
Open : Normal mode
Open : Normal mode